Page 1
CL-B101D40RPM(d0097) manual
• This meter has been designed specifically for RPM measurements.
Just enter the pules per revolution and the CL-B01DRPM bargraph
will calculate and display the RPM reading.
• Three ranges with resolution of 0.1 RPM, 1 RPM and 10 RPM
(99.99 x 1000 rpm max).
• Optional isolated 16 bit analog output. User or factory scalable
to 4 to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital
span from ± one count to the full scale range of 0 to 9999.
• Standard 101 segment Red Bar and Red 4-digit LED display with
a range of 0 to 9999. Optional Green Bar and Green Digital dis-
play. Also Optional Programmable Tricolor (Red-Green-Orange)
Bar is available.
• Front panel LED annunciators provide indication of setpoint status.
•
Two 9 Amp Form C, and two 4 Amp Form A or 4 x 4 Amp Form A
relays available.
• Provision to connect an external programming lockout switch.
• Provision for external DIM switch to reduce the brightest
display setting by 50%.
• Automatic intelligent averaging, smooths noisy signals while
providing a fast display response to real level changes.
• 24V excitation is available to power encoders or prox switches.
General Features
Specifications
Index
Software Features
Bargraph Center Point Display Mode Selection . . . 6
Bargraph Color Programming Mode . . . . . . . . 9
Case Dimensions . . . . . . . . . . . . . . . . . . . . . . . 7
Component Layout. . . . . . . . . . . . . . . . . . . . . 10
Connector Pinouts and Pin Descriptions. .10-11
Controls and Indicators . . . . . . . . . . . . . . . . . . 2
Setpoint Setting & Relay Configuration Mode. . . .8-9
Software Features . . . . . . . . . . . . . . . . . . . . . . 1
Software Logic Tree . . . . . . . . . . . . . . . . . . . . . 3
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 1
Two Point Analog Output Range Calibration . . . . . 7
Digital Span Selection for Bargraph Display . . 5
Digital Span Selection for Analog Range Output. . . 6
General Features . . . . . . . . . . . . . . . . . . . . . . . 1
I-Series Input Signal Conditioning Modules . . . . . 11
Ordering Information . . . . . . . . . . . . . . . . . . . 13
Programming Conventions. . . . . . . . . . . . . . . . 2
Input Specs: ..................Depends on Input signal conditioner
A/D Converter: ..............14 bit single slope
Accuracy: ......................±(0.05% of r 2 counts)
Temp. Coeff.: .................100 ppm/°C (Typical)
Warm up time: ...............2 minutes
Conversion Rate: ..........10 conversions per second (Typical)
Digital Display: ..............4 digit 0.56" LED red (std), green (optn)
Range 0 to 9999 counts.
Bargraph Display: .........101 segment 235º circular bar red (std),
green (optn)or tricolor (optn),
Polarity: .........................Assumed positive. Displays – negative
Decimal Selection: ........Front panel button selectable, X•X•X•X•
Positive Overrange: ......Bargraph and top segments of digital display
flash.
Negative Overrange: ....First segment of bargraph and bottom seg-
ments of digital display flash.
Relay Output: ................Two 9 Amp Form C relays, two 4 Amp Form
A relays or
4 x 4 Amp Form A relays.
Analog Output: .............Isolated 16 bit user scalable mA or V
OIC (mA out) ..............4-20 mA @ 0 to 500Ω max loop resistance
OIV (volts out) .............. 0-10 V DC @ 500 Ω or higher resistance
Power Supply: ...............AC/DC Auto sensing wide range supply
PS1 (std) ....................85-265 VAC / 95-300 VDC, 50-400Hz 4.2W
PS2 .............................18-48 VAC / 10-72 VDC, 50-400Hz 4.2W
Operating Temp.: ..........0 to 50°C
Storage Temp: ...............–20°C to 70°C
Relative Humidity: ........95% (non condensing)
Case Dimensions: ........Bezel (4.48"x4.48") 113.8x113.8mm
Depth behind bezel (4.23") 107.46 mm
Plus (0.48”) 12.24 mm for connectors
Weight: ...........................16 oz., 1lb 4 oz when packed
Smart 101 segment, 4 digit LED Tricolor or
Mono-color digital bargraph controller
with four fully programmable set points
in a switchboard style case for
RPM Measurement.
0.56”
LEDs
LEOPARD
FAMILY
• The bargraph can display, full
scale, any desired portion of
the digital reading.
• Setpoint 1 has delay-on-make
and delay-on-break plus
a special “pump on pump
off” mode that creates a
Hysteresis Band between SP1
and SP2.
• Four programmable setpoints
with adjustable Hysteresis.•
Bargraph center zero function.
• Relay activation can be select-
ed to occur above (hi) or below
(Lo) each setpoint.
• Decimal point setting.
• Digital display blanking.
• Four-level brightness control
