Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
Page 4
September 10, 2003 CM-35XTL Data Sheet(X08)
CM Case Dimensions and Panel Cutouts
Ordering Information
Standard Options for this Model Number
Part Number
Description
BASIC MODEL NUMBER
CM-35XTL
. . . . . . .3.5 digit LCD, 1V Drop, Loop Powered, 4-20mA
SPECIAL OPTIONS (Specify Req. Reading)
CB-FS35 . . . . . . . . .Non-Std Scale Changes, 3.5 Digit Meters
Special Options and Accessories
Part Number
Description
ACCESSORIES
CN-L10 . . . . . . . . . .PCB Edge Connector, Solder Type, Dual Row 10 Pins
CN-PUSH/CM . . . . .CM Series Push-on Screw Terminal Block Connector
SL.CASECLR . . . . . .Slim Bezel Case, Clear Faceplate w/Mtg Hardware
CM.CASECLR . . . . .Center Mount Case, Clear Faceplate w/Mtg Hardware
EM.CASECLR . . . . .End Mount Case, Clear Faceplate w/Mtg Hardware
TB-KIT . . . . . . . . . . .Replacement Terminal Block Connector Kit (3)
Many other options and accessories are available. See full price list for more details.
Prices subject to change without notice.
OPTIONAL TWIN MOUNTING OR
MULTIPLE ARRAY CASES
4"
(101.6mm)
2.52"
(64.2mm)
0.68"
(17.22mm)
3.32"
(84mm)
0.96"
(24.4mm)
0.304"
(7.72mm)
0.19"
(4.88mm)
1.17"
(29.7mm)
2.26"
(57.4mm)
2.76"
(69.75mm)
0.58"
(14.71mm)
0.95"
(24.23mm)
2.55"
(64.8mm)
0.97"
(24.6mm)
Front Panel Cutout
The Slim Bezel Case is supplied as standard. If specified at time of ordering, any combination of Twin Mounting and
Multiple Array Cases may be substituted at no additional cost. Extra cases may be ordered separately.
Insert DPM through cutout hole from front of
panel. Attach mounting brackets and screws as
shown, using second slot when panel thick-
ness is greater than 1/4 inch. Tighten screws
against rear of panel.
CENTER MOUNT CASE
Any number of Center Mount cases
may be fitted between two End Mount
cases for multiple arrays.
Part No.
CM-CASERED for LED's
CM-CASECLR for LCD's
SLIM BEZEL CASE
Standard Black ABS case with matte finish bezel for single
unit mounting.
Part No.
SL-CASERED for LED's
SL-CASECLR for LCD's
END MOUNT CASE
Same styling as Slim Bezel case but with bottom edge of
bezel removed. Two End Mount cases can be twin mounted
in a single cutout.
Part No.
EM-CASERED for LED's
EM-CASECLR for LCD's
1.17"
(29.7mm)
1.07"
(27mm)
0.97"
(24.5mm)
STANDARD SLIM BEZEL CASE
WARRANTY
Texmate warrants that its products are free from defects in material and workmanship under
normal use and service for a period of one year from date of shipment. Texmate’s obligations
under this warranty are limited to replacement or repair, at its option, at its factory, of any of the
products which shall, within the applicable period after shipment, be returned to Texmate’s facil-
ity, transportation charges pre-paid, and which are, after examination, disclosed to the satis-
faction of Texmate to be thus defective. The warranty shall not apply to any equipment which
shall have been repaired or altered, except by Texmate, or which shall have been subjected to
misuse, negligence, or accident. In no case shall Texmate’s liability exceed the original pur-
chase price. The aforementioned provisions do not extend the original warranty period of any
product which has been either repaired or replaced by Texmate.
USER’S RESPONSIBILITY
We are pleased to offer suggestions on the use of our various products either by way of print-
ed matter or through direct contact with our sales/application engineering staff. However, since
we have no control over the use of our products once they are shipped, NO WARRANTY
WHETHER OF MERCHANTABILITY, FITNESS FOR PURPOSE, OR OTHERWISE is made
beyond the repair, replacement, or refund of purchase price at the sole discretion of Texmate.
Users shall determine the suitability of the product for the intended application before using,
and the users assume all risk and liability whatsoever in connection therewith, regardless of any
of our suggestions or statements as to application or construction. In no event shall Texmate’s
liability, in law or otherwise, be in excess of the purchase price of the product.
Texmate cannot assume responsibility for any circuitry described. No circuit patent or software
licenses are implied. Texmate reserves the right to change circuitry, operating software, speci-
fications, and prices without notice at any time.
For product details visit www.texmate.com
Local Distributor Address
995 Park Center Drive • Vista, CA 92081-8397
Tel: 1-760-598-9899 • USA 1-800-839-6283 • That’s 1-800-TEXMATE
Fax: 1-760-598-9828 • Email: sales@texmate.com • Web: www.texmate.com
Texmate has facilities in Japan, New Zealand, Taiwan, and Thailand. We also have
authorized distributors throughout the USA and in 28 other countries.
Copyright © 2003 Texmate Inc. All Rights Reserved.
