Texmate DI-45U TIGER CUB User Manual Download

Page: 16 / 16

Texmate, Inc. Tel. (760) 598-9899

Page 16

3/31/00 DI-45U Data Sheet (DI2)

CALIBRATION

The DI-45U TIGER CUB is a precision digital panel instrument using
Dual Slope integration capable with 16 bit resolution employing 'intuitive
software' (available from the front panel or through the serial multiple
meter software interface) to select the input signal type and scaling. The
display averaging and rounding ensures stable displayed readings and
outputs. All signals may be scaled for desired engineering unit.

CALIBRATION: The DI-45U TIGER CUB meter is calibrated prior to
shipment, using equipment certified to NIST standards. Calibration con-
stants are stored in non-volatile memory in a EPROM. Recalibration for
units installed with a serial interface is completed using the application
software supplied with the meter. If the unit does not have a serial inter-
face, it must be returned to Texmate for recalibration.

CONNECTORS

The DI-45U TIGER CUB comes standard with plug-in screw terminal
blocks. To connect the instrument, make sure the screw terminal block is
securely attached to the pin socket on the printed circuit board. For each
input required, loosen the screw above the designated input (see specif-
ic module sheets or meter label for input diagrams), place input wire into
the square opening below screw, then retighten screw.

2-pin connector

4-pin connector

Connector attaches to meter here

Screw terminals for all connections

Texmate has facilities in Japan, New Zealand, Taiwan, and Thailand. We also

have authorized distributors throughout the USA and in 28 other countries

Local Distributor Address

995 Park Center Drive • Vista, CA 92083-8397
Tel: (760) 598-9899 • Fax: (760) 598-9828
URL: http://www.texmate.com

WARRANTY

Texmate warrants that its products are free from defects in material and workmanship under nor-

mal use and service for a period of one year from date of shipment. Texmate’s obligations under this
warranty are limited to replacement or repair, at its option, at its factory, of any of the products which
shall, within the applicable period after shipment, be returned to Texmate’s facility, transportation
charges pre-paid, and which are, after examination, disclosed to the satisfaction of Texmate to be thus
defective. The warranty shall not apply to any equipment which shall have been repaired or altered,
except by Texmate, or which shall have been subjected to misuse, negligence, or accident. In no case
shall Texmate’s liability exceed the original purchase price. The aforementioned provisions do not
extend the original warranty period of any product which has been either repaired or replaced by
Texmate.

USER’S RESPONSIBILITY

We are pleased to offer suggestions on the use of our various products either by way of printed

matter or through direct contact with our sales/application engineering staff. However, since we have
no control over the use of our products once they are shipped, NO WARRANTY WHETHER OF MER-
CHANTABILITY, FITNESS FOR PURPOSE, OR OTHERWISE is made beyond the repair, replace-
ment, or refund of purchase price at the sole discretion of Texmate. Users shall determine the suit-
ability of the product for the intended application before using, and the users assume all risk and lia-
bility whatsoever in connection therewith, regardless of any of our suggestions or statements as to
application or construction. In no event shall Texmate’s liability, in law or otherwise, be in excess of
the purchase price of the product.

Texmate cannot assume responsibility for any circuitry described. No circuit patent licenses are implied.

Texmate reserves the right to change circuitry, specifications, and prices without notice at any time.

CASE DIMENSIONS

TOP VIEW

87 mm

(3.425")

96 mm
(3.78")

91.6 mm
(3.6") (mosaic fitting)

96 mm
(3.78")

48 mm
(1.89")

41 mm
(1.61")

3.4 mm