Texmate, Inc. Tel. (760) 598-9899
•
www.texmate.com
Page 48
6/23/04 DI-50B51 320 Series (NZ306)
Data
Source
for
Analog
Outputs
1 & 2
Data
Source
for
Setpoints
Reset
Dest.
Reset
Source
Data
Source
for
Totalizers
1 & 2
Register Functions Register
Numbers
Data
Source
for
Displays
Data
Source
for
Peak &
Valley
R
e
gi
s
t
e
r
s
T
h
at
C
a
n
Be
S
e
l
e
c
t
e
d
B
y
F
r
o
n
t
P
a
n
e
l
Pu
s
h
B
u
tt
o
n P
r
og
r
a
mm
i
n
g
A Tiger 320 Series meter has 6,144 registers which are pro-
vided for use by the operating system and the powerful
Custom Macro Programming system (see page 11).
40 Manually Selectable Registers
Using the front panel buttons, there are 40 registers that
may be selected for use within the following functions:
•
[
CodE_1] - Display Configuration [X50]
. Selection of a
register as the data source for displays, peak and valley,
totalizers and analog outputs. (See pages 28 & 29)
•
Setpoint Control Settings [X1X]
. Selection of a register
as the data source for a setpoint. (See Page 46)
•
Setpoint Control Settings [XX7]
. Selection of a desti-
nation register that is to be reset by a setpoint with the
contents of a selected source register. (See Page 47)
•
Setpoint Control Settings [XX7]
. Select which register
’
s
contents are to be copied into the destination register by
a setpoint. (See Page 47)
The 40 registers that can be selected as a data source, a
reset source or a reset destination for the functions above
are shown in the table on the right.
The table shows, in seven columns, the functions where
these registers can be used.
Where a register is more likely to be used in a particular
function, a closed circle
●
is shown in the column. For those
functions where a register is less likely to be used, an open
circle
!
is shown.
No register number is shown for the first 11 functions,
because these 11 functions are identified in the display
menu for direct selection by their code names.
When cycling through the Registers Menu and then
Registers 1 to 244, the numerical Register Set will incre-
ment through each decade in turn, from 1 to 0, while the but-
ton is held down. When [200] is reached, [oFF] or [tArE] will
be displayed. To select a specific number set, the button
should be released and pressed again each time the left
most decade displays the desired number for that decade.
To quickly exit the numerical 1 to 244 Register Set, hold the
button down while cycling through the decades, and
release it when [oFF] or [tArE] appears.
Registers that Should Not be Used
The following registers are contained within the selectable 1
to 244 Register Set, but they should not be selected
because they are either reserved for future use, or for use
by the operating system only:
15, 38, 47-48, 52-53, 61-64, 123-128, 140-141, 234-244
Any selection of these Registers may cause a malfunction.
Resetting and Incrementing Using Setpoints
Setpoints may be used to reset and/or increment registers. In
the example shown on the right, 2 liter soft drink bottles are
being filled and packed 12 to a case. Using the setpoint reset
and increment feature, the number of bottles and the total
number of filled cases is easily calculated and displayed.
Totalizer 1 counts from 0 to 2, resets, and repeats. CH 2 counts
from 0 to 12, resets, and repeats.
Flow
Sensor
Channel 1
Flow Rate
Channel 3
Filled Cases
Totalizer 1
Flow
Channel 2
Bottles
SP5 = 2.00
Hi Setpoint
SP6 = 2.00
Hi Setpoint
SP4 = 12
Hi Setpoint
SP3 = 12
Hi Setpoint
S
O
U
R
C
E
R
E
S
E
T
R
E
S
E
T
I
N
C
R
E
M
E
N
T
I
N
C
R
E
M
E
N
T
S
O
U
R
C
E
S
O
U
R
C
E
S
O
U
R
C
E
USING SETPOINTS TO INCREMENT AND RESET REGISTERS
P
Use the
and
buttons to
cycle through the Registers Menu
and Registers (1 to 244). Press
the
button to make a selection.
P
[rESLt]
[Ch1]
[Ch2]
[Ch3]
[Ch4]
[tot_1]
[tot_2]
[PEAK]
[tArE]
[VALEY]
[diSP]
Display [diSP]
-
●
●
●
●
Result [rESLt]
-
●
●
●
●
●
●
●
CH1 [Ch1]
-
●
●
●
●
●
●
●
CH2 [Ch2]
-
●
●
●
●
●
●
●
CH3 [Ch3]
-
●
●
●
●
●
●
●
CH4 [Ch4]
-
●
●
●
●
●
●
●
Total 1 [tot_1]
-
●
●
●
●
●
●
Total 2 [tot_2]
-
●
●
●
●
●
●
Peak [PEAK]
-
!
●
!
●
Valley [VALEY]
-
!
●
!
●
Tare [tArE]
-
!
!
!
!
!
●
PID Output 1
50
!
!
!
!
PID Output 2
51
!
!
!
!
Smart Result 1
54
!
!
!
!
Smart Result 2
55
!
!
!
!
Smart Result 3
56
!
!
!
!
Smart Result 4
57
!
!
!
!
Smart Result 5
58
!
Smart Result 6
59
!
Smart Result 7
60
!
Analog Output 1
83
!
!
!
!
Analog Output 2
84
!
!
!
!
Timer 1
95
!
!
!
!
Timer 2
96
!
!
!
!
Smart Reset Offset 1
121
●
Smart Reset Offset 2
122
●
Clock - Seconds
213
!
Clock - Minutes
214
!
Clock - Hours
215
!
Clock - Days
216
!
Clock - Date
217
!
Clock - Month
218
!
Clock - Year
219
!
Setpoint Latch
221
●
Relay De-energize
222
●
Zero Offset - Result
227
!
Zero Offset - CH1
228
!
Zero Offset - CH2
229
!
Zero Offset - CH3
230
!
Zero Offset - CH4
231
!
[ 1]
[ 10]
[100]
[200]
[244]
