Texmate DI-60AE, Manual

Page 19

Apr-18-2016  DI-60A 320 DS (NZ302)_UL April 2016

Texmate, Inc. Tel. (760) 598-9899  •  www.texmate.com

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

X

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Step 1

Step 2

Step 3

Operational Display

Operational Display

Example

Press

2

Press

at same

time

Press

at same

time

Press

1

OR

Step 4

Press

at same

time

Press

at same

time

Step 6

0  Primary Display

1  Second Display (See Note)
2  Third Display (See Note)
3 Peak/Valley
4  Analog Output 1
5  Analog Output 2
6  Totalizer 1
7  Totalizer 2

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

OR

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

OR

Step 7

Step 8

Step 9

Press

1

Press

1

From Step 5

Step 5

Select [diSP] as the Data
Source from the options 
listed in the Select Data Source
diagram above.

Set Code 1 to [X50]:
1st Digit  = X Note relevant
2nd Digit  = 5 Selects data source mode
3rd Digit  = 0 Selects Primary Display

Select [000] to leave
Code 1

Save Data Source setting

Exit Code 2. Return to
Operational Display 

Enter Brightness Mode

Pass Brightness and
Calibration Modes
and enter Code 1 

X

CONFIGURE
DATA SOURCE

Go to Source
selection.

Go to the next
selection.

Example Procedure:

Configure the Primary Display with the display [diSP] as the 
data source by setting Code 1 to [

X50

]. See diagram at the 

 bottom of the page for data source selection options.

Configure Data Source Procedure

The following example procedure describes how to select the 
source of the data to be displayed for the third digit selection.

Programming Tip

 To enter the Main Programming Mode press the 

P

 and 

 buttons at the same time. To exit and return to the 

operational display, press the 

P

 and   buttons again 

at the same time.
 At the end of any procedure (Step 8 in this procedure) 
the 

P

  must be pressed before the 

P

and   buttons 

are pressed,otherwise the meter returns to the opera-
tional display without saving the new settings.

Programming Tip

Pressing the 

 and 

buttons at t h e 
same time increases the 
displayed parameter in 
increments of 100 counts.

Programming Tip

Pressing the 

button reaches 
[000] faster.

Note:

Options 1 and 2 listed fir the 3rd digit in Step 3 above are only for use 

with meters that have more than one display. With bargraph meters the 

PRIMARY display is the digital display, and the SECONDARY display 

is the bargraph display.

START HERE

Initial Setup Procedures

[CodE_1] - Display Configuration continued

Select Data Source

[TOT_1]

[TOT_2]

[TARE]

[VALLEY]

Use the     buttons to cycle through the 
Registers Menu and Registers (1 to 244) 
to select data source for displays (also 
see page 36).

[RESULT]

[CH1]

[CH2]

[CH3]

[CH4]

[PEAK]

[DISP]

[  1]

[ 10]

[100]

[200]

[244]

P