Texmate DI-60AE, Manual

Page 27

Apr-18-2016  DI-60A 320 DS (NZ302)_UL April 2016

Texmate, Inc. Tel. (760) 598-9899  •  www.texmate.com

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Press

1

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

CONFIGURE 
CH4 FUNCTIONS

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Step 1

Step 2

Step 3

Operational Display

Operational Display

Press

7

Press

at same

time

Press

at same

time

OR

Step 4

Press

at same

time

Press

at same

time

Step 5

CONFIGURING CH4 FUNCTIONS PROCEDURE

Pass Brightness Mode,
Calibration Mode, and 
Codes 1 to 5 and enter
Code 6

From Step 4

Set Code 6 to [01X]:
1st Digit  = 0 Selects direct display input
2nd Digit  = 1 Selects voltage, current
3rd Digit  = X Not relevant

Save CH4 setting

Exit Code 7. 
Return to
Operational Display 

Enter Brightness Mode

CODE 6 – CHANNEL 4 FUNCTIONS

FIRST DIGIT

SECOND DIGIT

THIRD DIGIT

FOR THERMOCOUPLE

0  Type J
1  Type K
2  Type R
3  Type S
4  Type T
5  Type B
6  Type N
7 Select user defined lineariza-

tion table (Table 1) set up in CAL 
[24X] 

FOR RTD TYPE (2-, 3-, 4- WIRE)

0 Resistance
1  RTD 385
2  RTD 392
3  RTD 120
4  Cn 10

MEASUREMENT TASK

0  No Function

1  Voltage / Current

2  TC (3rd digit selects type of 

TC). See Note 7

3  RTD (3rd digit selects type of 

RTD). See Note 7

4  Real Time Clock and Timer (3rd 

digit selects type)

5 -

6 -

7  Smart Input Module (3rd digit 

selects register)

FOR SMART INPUT MODULE

0  Output Register 1
1  Output Register 2
2  Output Register 3
3  Output Register 4
4  Output Register 5
5  Output Register 6
6  Output Register 7
7  Smart Input Module Register 3 

Code Setup

Note 7: 

For future development.

FOR REAL-TIME CLOCK & TIMER

0 HRS:MIN:SEC

1 HRS:MIN
2 -
3 -
4  1 2nd Count UP Timer
5  1 2nd Count DOWN Timer
6 -
7 -

Press

Use the

buttons to set the

required smart input module code 
(0 to 377). See 

I-Series Input 

Modules Guide (Z87)

 for code 

details.

Code 6 is a single code that 
combines all the configuration 
and post processing functions 
available for Channel 4.
When a 

quad input

 signal con-

ditioner is installed, the 4th input 
signal is processed and dis-
played on CH4.
Post processing and measure-
ment task functions for CH4 
are configured in the 1st, 2nd, 
and 3rd digits of Code 6. The 
 diagram opposite lists the avail-
able configuration selections in 
Code 6.

CH4 POST PROCESSING

0  Direct Display of Input (no pro-

cessing)

1  Square Root of Channel 4
2  Inverse of Channel 4
3  4 kB Meters
  32-point Linearization of CH4 using 

Table 1

  32 kB Meters
  32-point Linearization of CH4 using 

Table 4

Note:

All linearization tables are set up 
in the Calibration Mode [24X].

Example Procedure:

Configure CH4 as direct display of

voltage input by 

setting Code 6 to [

01X

].

START HERE

Initial Setup Procedures

[CodE_6] - Channel 4 Functions

See 

I-Series Input Modules Guide (Z87) 

for pro-

cedures to set up a quad input module.

P