Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
Page 12
DL-40JANUS-SG manual (d0116)
Case Dimensions
96 mm
(3.78")
48 mm
(1.89")
3.9 mm
(0.15") typical
FRONT VIEW
1/8 DIN 96x48mm
These dimensions are
increased by 1.6mm (0.06")
when the metal surround
case is installed.
The 96x48mm case is
particularly suitable for
mounting in mosaic panels
or insulative panels up to 2"
thick. They can also stack
mount, 2 up in existing
cutouts for 1/4 DIN
(96x96mm) or 4 up in
1/2 DIN (96X192mm).
NOTE: The Metal Surround Case
is pre-installed at the factory and cannot
be removed without damage to the case.
Metal Surround Case
P/N:(OP-MTL96X48)
uses
Metal Screw Mount Clips
and has a max. panel
thickness mounting
of 15.5 mm (0.61").
Removable
Key-lock
Cam
Opening
Safety
Catch
Clear Lockable NEMA 4X
Splash Proof Cover
P/N:(OP-N4/96x48)
40.8 mm
(1.61")
117 mm
(4.61")
SIDE VIEW
5.3 mm
(0.21")
3.7mm
(0.15")
43.4 mm
(1.71")
DIN Cutout spacers
Straight-thru Connector for
meters with output board
20mm (0.79")
Right-angled Connector
11.8mm (0.47")
PANEL CUTOUT
Case will mount in standard 1/8 DIN cutouts
45 mm
(1.77")
Snug Fitting
Mosaic Fitting
92 mm
(3.62")
Loose Fitting
91.6mm
(3.6")
40.8mm
(1.61")
8 places
3mm
(0.12")
8 places
4mm
(0.16")
43.4mm
(1.71")
1/8 DIN
Cutout spacers
87.4mm
(3.45")
Various bezel
colors are available.
Black is standard.
Prog.
SP3
SP4
SP2
SP1
For additional strength, extra Mounting
Slide Clips can be ordered and doubled up
one behind the other. P/N: (75-DMTCLIPF)
TOP VIEW
87.4mm
(3.45")
mosaic
fitting
95.4mm
(3.77")
Max. panel thickness
50mm
(1.97")
96 mm
(3.78")
91.6mm
(3.6")
DIN
Cutout
Spacer
To open rear cover,
use a small flat
bladescrew driver.
Press down lightly to
release catch on top
or bottom of case
and leaver outwards.
4.7mm
(0.19")
DIN Cutout Spacer
2mm
(0.08")
Connector
Socket
Prog.
SP1
SP1
SP2
SP4
SP3
SP5
SP6
Prog.
SP1
SP1
SP2
SP4
SP3
SP5
SP6
Prog.
SP1
SP1
SP2
SP4
SP3
SP5
SP6
When extra panel
mounting tightness is
required, order the
optional screw mount clip.
P/N:(OP-MTLCLIP)
High Strength Panel
Mounting Kit
P/N: OP-PMA96X48
For extra strength in portable applications, the 8 DIN
spacers should be snipped off and the Mosaic fitting
cutout used. Alternatively, the High Strength Panel
Mounting Kit (Part # OP-PMA96X48) can be used.
Panel adaptor plates are
available to retrofit most
existing panel cutouts.
Component Layout
INPUT MODULE
MAIN BOARD
MAIN BOARD HI VOLTAGE
MAIN BOARD LOW VOLTAGE
4 Wire / 6 Wire
Select Header
Excitation Range
Select Header
(5V or 10V)
mV/V Select Header
(2mV/V or 20mV/V)
2
20
mV/V
10V
5V
4W
6W
EXC
Pressure Transducer
PRESSURE
IS01:
Strain Gage/Pressure
151B
5/10V DC Exc., 20/2mV/V, 4/6-wire
