Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
Mar-07-2016 DI-50AN6 320 DS (NZ303)_UL_March 2016
Page 6
P
UP
Button
DOWN
Button
PROGRAM
Button
Display with Faceplate and Bezel
LED Annunciators
for Setpoints 1-6
Primary Display
Annunciator Panels
Front Panel Controls and Indicators
Program Button
While programming, pressing the
P
button saves the current
programming settings and moves to the next programming step.
You can move through the programming codes using the program
button. The codes you pass are not affected, unless you stop and
make changes using the or buttons.
Pressing the
P
and
button at the same time initiates the
main programming mode
. To save a new configuration set-
ting and return to the operational display, press the
P
button
once and then press the
P
and button at the same time.
Pressing the
P
and
button at the same time initiates the
setpoint programming mode
. To save a new configuration
setting and return to the operational display, press the
P
but-
ton once and then press the
P
and
button at t h e
same time.
See Display with Faceplate and Bezel diagram.
Up Button
When setting a displayed parameter during programming, press
the
button to increase the value of the displayed parameter.
When in the operational display, pressing the
button initiates
a viewing mode that allows you to view the readings on
chan-
nels 1 and 3, setpoints 1, 3, and 5, peak, and total 1
. Once
into the viewing routine, pressing the button moves through each
displayed parameter.
See Display with Faceplate and Bezel diagram.
Down Button
When setting a displayed parameter during programming, press
the
button to decrease the value of the displayed parameter.
When in the operational display, pressing the
button initiates
a viewing mode that allows you to view the readings on
channels 2 and 4, setpoints 2, 4, and 6, valley, and total 2
.
Once into the viewing routine, pressing the button moves
through each displayed parameter.
See Display with Faceplate and Bezel diagram.
Annunciator LEDs
The annunciator LEDs can be programmed to indicate the
alarm status.
Setpoint 1 can be configured to indicate the
rising
signal trend.
Setpoint 2 can be configured to indicate the
falling
signal trend.
They are labeled from left to right: SP1, SP2, SP3, SP4, SP5,
SP6.
See Display with Faceplate and Bezel diagram.
LED Display
The DI-50AN6 has a 5-digit, 7-segment, 8 mm (0.31”) stan-
dard red, or optional green or super-bright red, LED display.
The LED displays are used to display the meter input signal
readings. They also display the programming codes and set-
tings during meter programming.
Seven
Segment
LED Display
Display PCB without
Faceplate and Bezel
ON
1
2
SETPOINT
LOCKOUT
Switch
Annunciator
Panels
PROGRAM
LOCKOUT
Switch
Annunciator Panels
The annunciator panels are green or custom color 19 mm x
4 mm light bars. Each light bar can be customized to display
application specific text using a stick-on overlay.
Controls and Indicators
Controls and Indicators
Display Text Editing with 7 Segment
Alphanumeric Display Characters
Display text, such as setpoints, can be easily edited to suit your
application, by connecting the meter to a PC running the free
downloadable Configuration Utility program.
For Example:
Instead of [SP_1]
could be used for
TANK LOW
Instead of [SP_2]
could be used for
BRAKE OFF
OR
Scrolling Display Text Messaging
Scrolling display text messaging can be configured to run but
requires a simple compiler generated macro.
Display Text Characters
The following text characters are used with the 7-segment display.
7-SEGMENT DISPLAY CHARACTERS