Page 27
Apr-21-2016 DI-602A 320 DS (NZ313)_UL_April 2016
Texmate, Inc. Tel. (760) 598-9899 • www.texmate.com
To Step 5
From Step 4
Step 1
Step 2
Step 3
Step 5
Pass Brightness Mode,
Calibration Mode,
Codes 1 to 5, and
enter Code 6
Set Code 6 to [01X]
Exit Code 7. Return to
Operational Display
CONFIGURE
1st Digit = 0 Selects
direct display of input
2nd Digit = 1 Selects
voltage, current
3rd Digit = X Not
relavent
Enter Brightness Mode
CH4 FUNCTIONS
SP1
SP3
SP4
SP5
SP6
SP2
F1
P
F2
Operational Display
Press
at same
time
SP1
SP3
SP4
SP5
SP6
SP2
F1
P
F2
Press
7
OR
SP1
SP3
SP4
SP5
SP6
SP2
F1
P
F2
Press
at same
time
SP1
SP3
SP4
SP5
SP6
SP2
F1
P
F2
Operational Display
SP1
SP3
SP4
SP5
SP6
SP2
F1
P
F2
Step 4
Save CH4 setting
SP1
SP3
SP4
SP5
SP6
SP2
F1
P
F2
Press
1
CODE 6 – CHANNEL 4 FUNCTIONS
FIRST DIGIT
SECOND DIGIT
THIRD DIGIT
FOR THERMOCOUPLE
0 Type J
1 Type K
2 Type R
3 Type S
4 Type T
5 Type B
6 Type N
7 Select user defined lineariza-
tion table (Table 1) set up in CAL
[24X]
FOR RTD TYPE (2-, 3-, 4- WIRE)
0 Resistance
1 RTD 385
2 RTD 392
3 RTD 120
4 Cn 10
MEASUREMENT TASK
0 No Function
1 Voltage / Current
2 TC (3rd digit selects type of
TC).
See Note 7
3 RTD (3rd digit selects type of
RTD).
See Note
7
4 Real Time Clock and Timer (3rd
digit selects type)
5 -
6 -
7 Smart Input Module (3rd digit
selects register)
FOR SMART INPUT MODULE
0 Output Register 1
1 Output Register 2
2 Output Register 3
3 Output Register 4
4 Output Register 5
5 Output Register 6
6 Output Register 7
7 Smart Input Module Register 3
Code Setup
Note 7:
For future development.
FOR REAL-TIME CLOCK & TIMER
0 HRS:MIN:SEC
1 HRS:MIN
2 -
3 -
4 1 2nd Count UP Timer
5 1 2nd Count DOWN Timer
6 -
7 -
P
Press
Use the
buttons to set the
required smart input module code
(0 to 377). See
I-Series Input
Modules Guide (Z87)
for code
details.
Code 6 is a single code that
combines all the configuration
and post processing functions
available for Channel 4.
When a
quad input
signal con-
ditioner is installed, the 4th input
signal is processed and dis-
played on CH4.
Post processing and measure-
ment task functions for CH4
are configured in the 1st, 2nd,
and 3rd digits of Code 6. The
diagram opposite lists the avail-
able configuration selections in
Code 6.
CH4 POST PROCESSING
0 Direct Display of Input (no pro-
cessing)
1 Square Root of Channel 4
2 Inverse of Channel 4
3
4 kB Meters
32-point Linearization of CH4 using
Table 1
32 kB Meters
32-point Linearization of CH4 using
Table 4
Note:
All linearization tables are set up
in the Calibration Mode [24X].
Example Procedure:
Configure CH4 as direct display of
voltage input by
setting Code 6 to [
01X
].
START HERE
Initial Setup Procedures
[CodE_6] - Channel 4 Functions
See
I-Series Input Modules Guide (Z87)
for pro-
cedures to set up a quad input module.
