Texmate Tiger 320 DI-60E, Manual

Mar-14-2016 DI-60 320 DS (NZ301)_UL_March 2016

Page 27

Texmate, Inc. Tel. (760) 598-9899  •  www.texmate.com

CH4 POST PROCESSING

0  Direct Display of Input (no pro-

cessing)

1  Square Root of Channel 4
2  Inverse of Channel 4
3  32-point Linearization of CH4 using 

Table 4

CODE 6 – CHANNEL 4 FUNCTIONS

FIRST DIGIT

SECOND DIGIT

THIRD DIGIT

FOR THERMOCOUPLE

0  Type J
1  Type K
2  Type R
3  Type S
4  Type T
5  Type B
6  Type N
7  Select User Defined Table 1 set-up 

in Code 3 [X7X]. To invoke Table 1, 
reset Code 3 to [00X]  

FOR RTD TYPE (2-, 3-, 4- WIRE)

0 Resistance
1  RTD 385
2  RTD 392
3  RTD 120
4  Cn 10

MEASUREMENT TASK

0  No Function

1  Voltage / Current

2  TC (third digit selects type of 

TC).

 See Note 7

3  RTD (third digit selects type of 

RTD).

 See Note 

7

4  Real Time Clock and Timer 

(third digit selects type)

5 -

6 -

7  Smart Input Module (third digit 

selects register)

FOR SMART INPUT MODULE

0  Output Register 1
1  Output Register 2
2  Output Register 3
3  Output Register 4
4  Output Register 5
5  Output Register 6
6  Output Register 7
7  Smart Input Module Register 3 

Code Setup

Note:

For future development.

FOR REAL-TIME CLOCK & TIMER

0 HRS:MIN:SEC

1 HRS:MIN
2 -
3 -
4  1 Second Count UP Timer
5  1 Second Count DOWN Timer
6 -
7 -

P

Press

Use the

buttons to set the

required smart input module code 
(0 to 377). See 

I-Series Input 

Modules Guide (Z87)

 for code 

details.

Code 6 is a single code that 
combines all the configuration 
and post processing functions 
available for Channel 4.
When a 

quad input

 signal con-

ditioner is installed, the fourth 
input signal is processed and 
displayed on CH4.
Post processing and measure-
ment task functions for CH4 are 
configured in the first, second, 
and third digits of Code 6. The 
diagram opposite lists the avail-
able configuration selections in 
Code 6.

Example Procedure:

Configure CH4 for a

voltage input with the CH4 

processed input signal inversed

by setting Code 6 

to [

21X

].

Initial Setup Procedures

[CodE_6] - Channel 4 Functions

See 

I-Series Input Modules Guide (Z87) 

for pro-

cedures to set up a quad input module.

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Press

1

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Prog.

SP1

SP2

SP4

SP3

SP5

SP6

Step 1

Step 2

Step 3

Operational Display

Operational Display

Press

6

Press

at same

time

Press

at same

time

OR

Step 4

Press

at same

time

Press

at same

time

Step 5

CONFIGURING CH4 FUNCTIONS PROCEDURE

Pass Brightness Mode,
Calibration Mode, and 
Codes 1 to 5 and enter
Code 6

From Step 4

To Step 5

X

1st Digit  = 2 Selects inverse of CH4
2nd Digit  = 1 Selects voltage, current
3rd Digit  = X Not relevant

Save CH4 setting

Exit Code 7. Return to

Operational Display 

Enter Brightness Mode