background image

EK1230L and EK1230CL Crimping Tools

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

3

IMPORTANT SAFETY INFORMATION

SAFETY 

ALERT 

SYMBOL

This symbol is used to call your attention to hazards 

or unsafe practices which could result in an injury or 

property damage. The signal word, defined below, 

indicates the severity of the hazard. The message 

after the signal word provides information for pre-

venting or avoiding the hazard.

Immediate hazards which, if not avoided, WILL result 

in severe injury or death.

Hazards which, if not avoided, COULD result in 

severe injury or death.

Hazards or unsafe practices which, if not avoided, 

MAY result in injury or property damage.

Read and understand all of the 

instructions and safety information 

in this manual before operating or 

 servicing this tool.
Failure to observe this warning 

could result in severe injury or death.

Electric shock hazard:
This tool is not insulated. When 

using this unit on or near energized 

electrical lines, use proper personal 

protective equipment.
Failure to observe this warning 

could result in severe injury or death.

Wear eye protection when operating 

or servicing this tool. 
Failure to wear eye protection could 

result in serious eye injury from 

flying debris or hydraulic oil. 

Skin injection hazard:
Do not use hands to check for oil 

leaks. Oil under pressure easily 

punctures skin. If injured, seek 

medical attention immediately to 

remove oil.
Failure to observe this warning 

could result in serious injury, gan-

grene, or death.

Do not use solvents or flammable 

liquids to clean the tool body. 

Solvents or flammable liquids could 

ignite and cause serious injury or 

property damage.

An incomplete crimp can cause a fire.
•  Use proper die, connector, and cable combina-

tions. Improper combinations can result in an 

incomplete crimp.

•  The relief valve sounds and the ram automatically 

retracts to indicate a completed crimp. If you do 

not hear the sound of the relieve valve or the ram 

does not automatically retract, the crimp is not 

complete.

Failure to observe these warnings could result in 

severe injury or death.

Summary of Contents for EK1230L











Reviews: