background image

Greenlee / A Textron Company

4455 Boeing Dr. • Rockford, IL 61109-2988 USA • 815-397-7070

7

EK1550LT and EK1550LX Battery-powered Crimping Tools

Adapter Kits

 (cont’d)

Procedure for Using Thomas & Betts TBM15 Dies; 

48788 Die Holder Kit

1.  Install the upper 48789 die holder assembly in hole 

in top of “C” head. Snap in place with top die holder 

retaining spring plunger (6).

2.  Install lower 48789 die holder assembly in hole in 

end of piston. Snap in place with bottom die holder 

retaining spring plungers (6).

3.  Select proper die set for fitting to be crimped.
4.  Slide top die into place in die holder while depress-

ing die retainer button. Release die button while it 

snaps into place, locking die into position. Repeat 

operation for other die entry.

Procedure for Using Burndy Y46 Dies; 

48820 Die Holder Kit

1.  Install the upper 48822 die holder assembly in hole 

in top of “C” head. Snap in place with top die holder 

retaining spring plunger (6).

2.  Install lower 48821 die holder assembly in hole in 

end of piston. Snap in place with bottom die holder 

retaining spring plungers (6).

3.  Select proper die set for fitting to be crimped.
4.  Slide top die into place in die holder while simulta-

neously squeezing both retainer buttons. Release 

buttons and allow them to snap into place. Repeat 

operation for other die entry.

48788 Die Holder Kit contains: 

(2) 48789 Die Holders

48820 Die Holder Kit contains (1) each: 

48822 Upper Die Holder and 48821 Lower Die Holder

48789 TBM15 DIE

HOLDER ASSEMBLIES

BOTTOM DIE

HOLDER RETAINING

SPRING PLUNGERS (6)

TOP DIE

HOLDER 

RETAINING

SPRING

PLUNGER (6)

BOTTOM DIE

RETAINING MECHANISM

TOP DIE

RETAINING

MECHANISM

48822 Y46 DIE

HOLDER ASSEMBLY

BOTTOM DIE

HOLDER RETAINING

SPRING PLUNGERS (6)

BOTTOM DIE

RETAINING

MECHANISM (2)

TOP DIE

RETAINING

MECHANISM (2)

TOP DIE HOLDER

RETAINING SPRING PLUNGER (6)

Summary of Contents for Greenlee EK1550LT

















Reviews: