29
28
METEOTIME PRIMO –
Weather Info Center
SET
<1>
Accept the selected letter and go to the next position.
OR
<2>
If you have not entered any letter and the cursor is flashing at the last position, confirm
the entry with this button and your place will also be included in the memory with
immediate effect.
TEST
One position back in the data entry process.
**The place that you have selected to enter your own description will still exist under its own name.
• Press the
SET
button to confirm and exit.
• On the display appears
EINST.VORG
(EXIT in English).
7.4 Time zone and language settings
• Press and hold the
SET
button for 3 seconds, until
LAND EINST.
(COUNTRY in English) appears on the display.
• Press the
SET
button again, then
ZONE +OOH
appears on the display. Press the
+
or
–
button to adjust the time
zone.
• Press the
SET
button again, then the language appears on the display. Press the
+
or
–
button to select your
desired language. There are seven languages available in total: German, Swedish, Dutch, Italian, French, Spanish
and English.
• Press the
SET
button.
EINST.VORG
. (EXIT in English) appears on the display. After 4 seconds, it will change to the
Date-Time Mode.
ATTENTION:
The setting mode is automatically terminated after approx. 30 seconds if no settings are made within
this time.
7.5 Switch day-weather information
↔
night-weather information
• The device can to automatically switch to the day-weather (6 am to 6 pm)and night-weather (6 pm to 6 am)
respectively. The
DAY / NIGHT
button can be used to give a forecast of the DAY (for 10 seconds) if you are cur-
rently viewing forecasts for the NIGHT, or vice versa.
METEOTIME PRIMO –
Weather Info Center
7.6 Critical weather information
(see Meteotime Booklet)
• The Meteotime weather signal contains critical weather information such as: wind gust, freezing rain, heavy snow,
thunder, strong UV, dense fog, etc. for today and the coming three days. In this case a warning symbol
for
critical weather conditions will be activated.
• Sometimes there is more than one critical weather situation in 4 days. Press the
DAY / NIGHT
button to view the
critical weather information one by one. The warning symbol for the corresponding day will flash.
• If no button is pressed, the critical weather information will be displayed, so as to make sure you are aware of the
critical weather details.
8. Weather symbols
(see Meteotime Booklet)
• There are total 15 weather symbols for the day and 15 weather symbols for the night.
9. Maximum and minimum values
• The maximum and minimum indoor and outdoor temperature and humidity values will be automatically stored in
the memory of the weather station. To display the values, press the
MEM
button and the corresponding indicators,
MAX or MIN will appear.
• Press the
MEM
button for about 3 seconds to erase the stored data.
10. Additional outdoor transmitters
• You can use the transmitter Cat. No. 30.3244.02 as a replacement or additional transmitter for your weather sta-
tion
Meteotime PRIMO
.
• When having more than one external transmitter, select a different channel for each one with the
CH
switch inside
the transmitter's battery compartment.
• Insert two new batteries AAA 1,5 V, into the outdoor transmitter's battery compartment. Make sure the polarities
are correct.
• Select a free channel with the
CHANNEL
button on the base station.
• Press and hold the
–
button on the base station for three seconds to start the initialisation manually.
• The reception symbol will be flashing above the channel number.
• As soon as the outdoor values have been received, the reception symbol will stay on the display and the received
outdoor values appear.
01_TFA_No. 35.1156_Anleitung 29.11.2019 6:59 Uhr Seite 15