background image

KEY # PART DESCRIPTION 

PART # 

Hopper Assembly 

16591 

Hopper * 

16592 

Hopper Spacer (set of 4) 

16603 

Shutoff Plate Guide * 

14836-1 

Shutoff Plate * 

16594 

Impeller Shaft Bearing Assembly * 

14312-1 

Impeller Assembly (includes #8 thru #11) 

16596 

Impeller 

16597 

Impeller Shaft 

16598 

10 

Gear Carrier, Complete w/ Grease Fittings 

780155 

11 

Pinion Gear 

780122 

12 

Idler Wheel 

14857 

13 

Retainer Clip (set of 3) 

780180 

14 

Gearbox Cover Half (set of 2) 

780110 

15 

Frame Assembly (includes #17) 

16600 

16 

Axle 

16599 

17 

Axle Bearing  (set of 4) 

16412 

18 

Axle Collar (set of 3) 

780200 

19 

Ring Gear 

780121 

20 

Drive Wheel 

14856 

21 

Rest 

16604 

22 

Upper Handle Assembly (includes #23 & #25) 

15512 

23 

Hand Grips (set of 2) 

14870 

24 

Upper Handle 

15498 

25 

Main Shutoff Lever Assembly 

15513 

26 

Shutoff Plate Link * 

14846 

27 

Pivot Lever Assembly * 

14878 

28 

Lower Control Rod w/ swivel * 

14917 

29 

Rate Control Spring * 

13354 

30 

Rate Control Knob/Washer * 

12704 

31 

Control Tube 

14916 

32 

Rate Control Plate * 

16595 

33 

Rate Control Housing * 

15527 

34 

Pointer * 

12708 

35 

Hopper Screen Clip (set of 2) 

780440 

36 

Agitator Pin 

780100 

37 

Hopper Screen 

14863 

38 

Fastener Pack 

15579-1 

39 

Hopper cover 

14606-1 

40 

Calibration Key (see calibration instructions) 

15740 

— 

Optional Side Deflector Kit 

(Product Code SDSHIELDLCO) 

16579 

Ordering Parts 

1)  Part number (DO NOT use key numbers when ordering parts. ALWAYS use part numbers.) 

 

2)   Part description 

 

3)   The Andersons model LCO1000 (product code ASPLCO1000) 

See diagram for assistance in identifying specific parts. 

 

For parts orders, call 1-800-294-0671. (Note: Sales of parts for the Andersons spreaders are handled by EarthWay

IMPORTANT: When ordering replacement parts, always provide the following information: 

 

   
 
 

  
For More 
  Information 
  Call . . . 

 

1-800-225-2639 

                               (U.S. Only) 

 

The Andersons’ toll-free 

Helpline. This helpline is  

provided to give you more 

Information about 

Andersons Turf Products. 

……………………………….. 

 
 
 
 

 

  

 

Or Visit Our 

  Website At … 

www. andersonsturf.com 

 

The Andersons, Inc. 

480 Dussel Drive 

Maumee, OH 43537 USA 

* Indicates parts in Hopper Assembly 

Summary of Contents for LCO-1000









Reviews: