In Stock Workstations / WashStations
™
with DryDock
™
4
Side view applies to all
DryDock™ Workstations shown
IW
S 4S + DD18
IW
A 4S + DD18
IW
S 4S + DD12
IW
A 4S + DD12
IW
S 3S + DD18
IW
A 3S + DD18
IW
S 3S + DD12
IW
A 3S + DD12
18” Finished cutout
1/2” Reveal front
and back
10”
16”
IW
S 30S + DD18
IW
A 30S + DD18
IW
S 30S + DD12
IW
A 30S + DD12
I.D. 17”
(432 mm)
O.D. 39 1/2”
(1003 mm)
I.D. 26”
(660 mm)
I.D. 12”
(305 mm)
C.O. 18”
(457 mm)
O.D. 19 1/2”
(495 mm)
C.O. 38 1/2”
(978 mm)
13 1/4”
(337 mm)
25 1/4”
(641 mm)
8”
(203 mm)
8”
(203 mm)
I.D. 17”
(432 mm)
O.D.
45 1/2”
(1156 mm)
C.O.
44 1/2”
(1130 mm)
13 1/4”
(337 mm)
31 1/4”
(794 mm)
I.D.
26”
(660 mm)
I.D.
18”
(457 mm)
C.O. 18”
(457 mm)
O.D. 19 1/2”
(495 mm)
8”
(203 mm)
8”
(203 mm)
I.D. 17”
(432 mm)
O.D. 45 1/2”
(1156 mm)
I.D. 32”
(813 mm)
I.D. 12”
(305 mm)
C.O. 18”
(457 mm)
O.D. 19 1/2”
(495 mm)
C.O. 44 1/2”
(1130 mm)
16 1/4”
(413 mm)
28 1/4”
(718 mm)
8”
(203 mm)
8”
(203 mm)
I.D. 17”
(432 mm)
O.D.
51 1/2”
(1308 mm)
I.D.
32”
(813 mm)
I.D.
18”
(457 mm)
C.O. 18”
(457 mm)
O.D. 19 1/2”
(495 mm)
C.O.
50 1/2”
(1283 mm)
16 1/4”
(413 mm)
34 1/4”
(870 mm)
8”
(203 mm)
8”
(203 mm)
I.D. 17”
(432 mm)
O.D. 63 1/2”
(1613 mm)
I.D. 44”
(1118 mm)
I.D. 18”
(457 mm)
C.O. 18”
(457 mm)
O.D. 19 1/2”
(495 mm)
C.O. 62 1/2”
(1587.5 mm)
22 1/4”
(565 mm)
40 1/4”
(1022 mm)
8”
(203 mm)
8”
(203 mm)
I.D. 17”
(432 mm)
I.D. 44”
(1118 mm)
I.D. 12”
(305 mm)
C.O. 18”
(457 mm)
O.D. 19 1/2”
(495 mm)
22 1/4”
(565 mm)
34 1/4”
(870 mm)
8”
(203 mm)
8”
(203 mm)
O.D. 57 1/2”
(1460.5 mm)
C.O. 56 1/2”
(1435 mm)
SUGGESTED GALLEY TAP AND TAP ACCESSORIES PLACEMENT GUIDE
Suggested maximum inside corner radius of countertop cutout 3/8”
Galley Tap 1 3/8” min hole diameter (1 1/2" min hole diameter for fast water jet cut)
Center Tap hole diameters 2” behind cutout
Note: Galley Hot & Cold Tap requires a minimum 8" clearance to center if installed to the right of the Galley Tap
Note: Tap Placements are for right hand or left hand drain orientation
Call 800.375.4255 or email customerservice@thegalley.com
for additional guidance on Tap and Tap Accessory placements
