background image

Owner's Manual

D3676/D3677/D3678/D8576
What This Owner's Manual Can Do For You

  -  It explains exactly how The Rite Door

® 

 

operates.

  -  It explains periodic maintenance requirements necessary to assure reliable operation.
  -  It explains simple things to do and check before you call for service, so you may save the cost of an 
     unnecessary service call.
  -  It provides a complete listing of service replaceable parts.
  -  It provides your Adams Rite Limited Warranty and what steps to take for service.

Owners Record

The model number is located on the hinge stile mounting base. Refer to this number and the additional informa-
tion below when you call upon your local Rite Door

®

 dealer regarding this product.

Model No: D3676/D8576/D3677/D3678
Finish:
Door Size:
Hardware Supplier:
Date Installed:

Exit Device Operation

The Rite Door

®

 Top Rod Concealed Vertical Rod (CVR) devices provides for life safety, security & fire containment 

by use of a rotating top latch and post type header strike. When the push bar is depressed, the top rod retracts to 
release the door. Upon closing, the top actuator deadlatches around the top strike post securing the door.

Fire Door Labels, Strikes and Frame Screws

Fire Door Labels and other misc. hardware will be located in a removable channel located at the top of the door. 
This channel is secured by two Phillips head screws that can be easily removed. Please contact the factory im-
mediately if this hardware can not be located.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

    

 

 

 

 

     

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for D3676











Reviews: