background image

It is designed for maximum performance.  Please seek advice if one is not familiar with this kind
of electric powered precision model.  Operating this model without prior preparation may cause
injuries.  Remember, safety  is the most important thing.  Always  keep this instruction manual at
hand for quick reference.

Warning ! This model is not a toy.

THE WINGS MAKER

FACTORY PRE-FABRICATED

ALMOST-READY-TO-FLY (ARF) SERIES

MADE IN CHINA

* Specifications are subject to change without notice.*

www thewingsmaker com

.

.

Specifications

Specifications

Before commencing assembly please read these instructions thoroughly

,

.

I NST RUCT I ON M ANUAL

Wing Span: 36.5 in / 930 mm
Wing Area: 346 sq in / 22.3 sq dm
Flying Weight: 19-23 oz / 540-650 g
Fuselage Length: 41.5 in / 1055 mm
Requires: 4-channel radio w/ 4 micro servos. Outrunner
                  Motor KM0283010 w/ Propeller Adaptor HW2340100
                  20A Brushless ESC, 2 cells 7.4V 15C 1300 mAh
                  (indoor flying) to 3 cells 11.1V 15C 1800 mAh
                  (outdoor flying) Li-Po battery & charger.

GE039PO22591118

Handyman EP

Summary of Contents for Handyman EP













Reviews: