background image

THE WINGS MAKER

FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF)  SERIES
MADE IN CHINA

* Specifications are subject to change without notice.*

Warning !  This model is not a toy.

www.thewingsmaker.com

INSTRUCTION  MANUAL

Before commencing assembly, please read these instructions thoroughly.

It is designed for maximum performance.  Please seek advice if one is not familiar with this kind
of engine(electric) powered precision model.  Operating this model without prior preparation may 
cause injuries.  Remember, safety is the most important thing.  Always keep this instruction 
manual at hand for quick reference.

Specifications

Wing Span: 50 in / 1270 mm
Wing Area: 484 sq in / 31.2 sq dm
Flying Weight: 3.5 lbs / 1600 g
Fuselage Length: 44.5 in / 1130 mm
Requires: (Engine powered) 2-stroke 0.40 engine 
                      4-channel radio w/ 4 standard servos
                      (Electric powered) 450W motor system 
                      4-channel radio w/ 3 standard servos 
                      40A  brushless ESC with 11x8E propeller, 4 cells 
                      14.8V 3200 mAh Li- Po battery & charger

GA029PO22471104

Summary of Contents for Wingman II

















Reviews: