The World Models Manufacturing SPORT WINGS 90 Instruction Manual Download

Page: 1 / 12

THE WINGS MAKER

FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA

* Specifications are subject to change without notice.*

It is designed for maximum performance.

Please seek advice if one is not familiar with this kind

of engine powered precision model.

Operating this model without prior preparation may cause

injuries.

Remember,

safety is the most important thing.

Always keep this instruction manual at

hand for quick reference.

Warning !

This model is not a toy.

Wing Span

81 in / 2050mm

Wing Area

1020 sq in / 65.8 sq dm

Flying Weight

9 lbs / 4100 g

Fuselage Length

61 in / 1560mm

Radio required: 4 - stroke 0.91 engine

4 - channel radio w/ 5 servos

Specifications

Before

commencing

assembly

please

read

these

instructions

thoroughly

Specifications

www

thewingsmaker

com

INSTRUCTION MANUAL

GA011

Summary of Contents for SPORT WINGS 90













Search results

Summary of Contents for SPORT WINGS 90

Reviews:

Related manuals for SPORT WINGS 90

Brands by name

Popular brands

The World Models Manufacturing SPORT WINGS 90, Instruction Manual

Search results

Summary of Contents for SPORT WINGS 90

Reviews:

Related manuals for SPORT WINGS 90

Brands by name

Popular brands