THE WORLD MODELS P-40 Warhawk Instruction Manual Download

Page: 7 / 16

P.6

Elevator Pushrod

Rudder Pushrod

PB2x14mm

Screw

PB2x14mm

Screw

Ø1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

Ø1mm pilot holes for World Models tri-horn are pre-drilled.

Please look for pin-hole marks at under side of control surfaces.

Fuel Tube

Ø6x5mm

Tri-horn

M3 x 14mm(L)

PB2x14mm

Elevator Pushrod

Ø1.8x457mm

Clevis

Bottom View

TWM PL8210010

CLEVIS WRENCH

TWM PL8210010

CLEVIS WRENCH

Engine Mount

M4x25mm

Socket Head Screw

d4xD9mm

Washer

Apply thread locker to screws

Blind nuts are off-centered to keep

the spinner at the fuselage axis.

d4xD9mm Washer

Socket Head Screw

M4x25mm

Engine Mount

PL5111050

165mm

40mm

50mm

130mm

Tri-horn

M3 x 14mm(L)

Fuel Tube

Ø6x5mm

Clevis

Rudder Pushrod

Ø1.8x560mm

PB2x14mm

Summary of Contents for P-40 Warhawk

















Search results

Summary of Contents for P-40 Warhawk

Reviews:

Related manuals for P-40 Warhawk

Brands by name

Popular brands

THE WORLD MODELS P-40 Warhawk, Instruction Manual

Search results

Summary of Contents for P-40 Warhawk

Reviews:

Related manuals for P-40 Warhawk

Brands by name

Popular brands