THE WORLD MODELS Super Chipmunk-90 RF Instruction Manual Download

Page: 5 / 16

Wing joiner

9x24x223mm

Aileron Servo

PWA2 x 8mm

Screw

PB2x16mm

Screw

PB2x20mm

Screw

Ø1mm pilot holes for World Models tri-horn

pre-drilled.Please look for pin-hole marks

at under side of control surfaces.

P.4

PWA2x8mm

PB2x20mm

PB2x16mm

PB2x20mm

FuelTube

Tri-Horn

M3x9mm

Please dry fit wing joiner into left and right wing to make sure they fit with the proper

dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to both sides of

all surfaces in contact. Use a stick to apply the glue to inner side of wing joiner sleeve,

and apply the glue to wing joiner before putting them together. Wing joiner not glued

properly will lead to wing failure and plane crash.

Main Wing

ForFlapServo

LeadtoAileronServo

Straper

FuelTube

A004NPO31351603

Summary of Contents for Super Chipmunk-90 RF

















Search results

Summary of Contents for Super Chipmunk-90 RF

Reviews:

Related manuals for Super Chipmunk-90 RF

Brands by name

Popular brands

THE WORLD MODELS Super Chipmunk-90 RF, Instruction Manual

Search results

Summary of Contents for Super Chipmunk-90 RF

Reviews:

Related manuals for Super Chipmunk-90 RF

Brands by name

Popular brands