EX-TRACK
®
Operator Manual, Revision T-1
4
5.1.1. Input voltage settings ...................................................................................... 33
5.1.2. EX-TRACK
®
placement ..................................................................................... 33
5.1.3. Oxy fuel nozzle choice ..................................................................................... 33
5.1.4. Regulated gas supply ...................................................................................... 33
5.1.5. Oxy fuel cut charts ............................................................................................ 33
5.1.6. Pre-ignition check ............................................................................................. 34
5.2. Ignition and flame adjustment - oxy propane cutting .................................... 34
5.3. Cut quality ............................................................................................................ 35
5.4. Preheat time ......................................................................................................... 35
5.5. Torch operation .................................................................................................... 35
5.6. Flashback and backfire prevention ................................................................... 36
5.6.1. Flashback prevention ..................................................................................... 36
5.6.2. Backfire prevention ......................................................................................... 36
6. SYSTEM OPERATION ...............................................................................38
6.1. Oxy fuel cutting (prior to operation) ................................................................. 39
6.2. Plasma arc cutting (prior to operation) ............................................................. 40
7. MAINTENANCE .......................................................................................41
7.1. Cleaning the system ............................................................................................ 42
7.2. System lubrication ............................................................................................... 42
7.3. Drive motor adjustment ...................................................................................... 42
7.4. Oxy fuel nozzle maintenance ............................................................................. 42
8. CIRCUIT DIAGRAM ..................................................................................43
8.1. Plasma interface ................................................................................................... 44
9. OPERATION .............................................................................................45
9.1. Control panel functions ...................................................................................... 48
9.2. CNC system functions ......................................................................................... 48
9.3. System main menu .............................................................................................. 49
9.3.1. Menu features ................................................................................................... 49
9.3.2. Main function F-key menu ............................................................................... 50
9.4. Automatic function .............................................................................................. 50
9.4.1. Interfaces and inputs ....................................................................................... 51
9.4.1.1. Speed ............................................................................................................. 51
9.4.1.2. Prog, pierce, kerf .......................................................................................... 51
9.4.1.3. Work mode - running status ....................................................................... 51
9.4.1.4. Input and output signals ............................................................................. 51
9.4.1.5. System parameters display ......................................................................... 51
9.4.1.6. System coordinates display ......................................................................... 52
9.4.1.7. Zoom function [key 1] ................................................................................... 52
9.4.1.8. Return [key 2] ................................................................................................. 52
Summary of Contents for EX-TRACK
