EX-TRACK
®
Operator Manual, Revision T-1
47
9.10.6. System axes .................................................................................................... 77
9.10.7. G-codes .......................................................................................................... 78
9.10.8. G92 – program zero point ............................................................................. 78
9.10.9. G90 – absolute commands ........................................................................... 78
9.10.10. G91 – incremental commands .................................................................. 78
9.10.11. G20 – imperial mode .................................................................................. 78
9.10.12. G21 – metric mode ...................................................................................... 78
9.10.13. G00 – rapid travel ......................................................................................... 79
9.10.14. G01 – linear interpolation (motion in a straight line) .............................. 79
9.10.15. G02- G03 – circular interpolation (motion along a circular arc) ............. 79
9.10.16. G04 – pause/dwell ....................................................................................... 79
9.10.17. G40 – kerf off (compensation factor) ......................................................... 79
9.10.18. G41 – kerf left ............................................................................................... 80
9.10.19. G42 – kerf right ............................................................................................. 80
9.10.20. G28 – return to reference point (zero position) ........................................ 80
9.10.21. G22 / G80 – cycle command (loop function) ........................................... 80
9.11. M - codes ............................................................................................................ 80
9.11.1. M00 - stop ....................................................................................................... 80
9.11.2. M02 – program end ...................................................................................... 80
9.11.3. M07 – cutting sequence start ....................................................................... 80
9.11.4. M08 – cutting sequence stop ....................................................................... 81
9.11.5. Additional M-codes ....................................................................................... 81
Summary of Contents for EX-TRACK
