background image

Page 4

Appliance Installation:

Appliance Installation:

Appliance Installation:

Appliance Installation:

Appliance Installation:

The PHE unit can be mounted on
a wall or suspended from a
cabinet.  Both vertical and
horizontal discharge are possible
with either mounting method.

Dischar

Dischar

Dischar

Dischar

Discharge Dir

ge Dir

ge Dir

ge Dir

ge Direction:  

ection:  

ection:  

ection:  

ection:  

The PHE

hood is shipped ready for vertical
discharge.  To change to horizon-
tal discharge simply move the two
plates marked 

A

A

A

A

A

 in Figure 1 to

the top of the hood.  Each plate is
held in place by two sheetmetal
screws.

Assembly of the T

Assembly of the T

Assembly of the T

Assembly of the T

Assembly of the Transition:

ransition:

ransition:

ransition:

ransition:

The transition supplied with the
PHE hood mounts to the top or
rear of the hood depending on the
discharge direction.

1.  Align mounting holes at base
of transition with mounting holes
on 1/2” flange located at the top
or rear of the hood depending on
direction of discharge.

2.  Fasten transition to hood
using 6 (4 mm x 9.5 mm) screws
(included with hood).

3.  Duct tape connection between
transition and hood.

4.  Remove tape holding damper
closed.

Figure 1

Summary of Contents for PHE














Reviews: