CUTMASTER 40MM
OPERATION
Manual 0-5084
4T-10
4T.08 Recommended Cutting Speeds for SL100 Torch With Exposed Tip
Type Torch: SL100 With Exposed Tip
Type Material: Mild Steel
Type Plasma Gas: Air
Type Secondary Gas: Single Gas Torch
Thickness
Tip
Output
Amperage Speed (Per Minute)
Standoff
Plasma Gas Press
Flow (CFH)
Pierce
Pierce Height
Inches mm (Cat. No.) Volts(VDC) (Amps)
Inches
Meters
Inches mm
psi*
bar
Plasma Total** Delay (Sec) Inches mm
0.036 0.9 9-8208
104
40
340
8.64
0.19 4.8
65
4.5
55
170
0.00
0.2
5.1
0.06 1.5 9-8208
108
40
250
6.35
0.19 4.8
65
4.5
55
170
0.10
0.2
5.1
0.075 1.9 9-8208
108
40
190
4.83
0.19 4.8
65
4.5
55
170
0.30
0.2
5.1
0.135 3.4 9-8208
110
40
105
2.67
0.19 4.8
65
4.5
55
170
0.40
0.2
5.1
0.188 4.8 9-8208
113
40
60
1.52
0.19 4.8
65
4.5
55
170
0.60
0.2
5.1
0.25 6.4 9-8208
111
40
40
1.02
0.19 4.8
65
4.5
55
170
1.00
0.2
5.1
0.375 9.5 9-8208
124
40
21
0.53
0.19 4.8
65
4.5
55
170
NR
NR
NR
0.500 12.7 9-8208
123
40
11
0.28
0.19 4.8
65
4.5
55
170
NR
NR
NR
0.625 15.9 9-8208
137
40
7
0.18
0.19 4.8
65
4.5
55
170
NR
NR
NR
Type Torch: SL100 With Exposed Tip
Type Material: Stainless Steel
Type Plasma Gas: Air
Type Secondary Gas: Single Gas Torch
Thickness
Tip
Output
Amperage Speed (Per Minute)
Standoff
Plasma Gas Press
Flow (CFH)
Pierce
Pierce Height
Inches mm (Cat. No.) Volts(VDC) (Amps)
Inches
Meters
Inches mm
psi*
bar
Plasma Total** Delay (Sec) Inches mm
0.036 0.9 9-8208
103
40
355
9.02
0.125 3.2
65
4.5
55
170
0.00
0.2
5.1
0.05 1.3 9-8208
98
40
310
7.87
0.125 3.2
65
4.5
55
170
0.00
0.2
5.1
0.06 1.5 9-8208
98
40
240
6.10
0.125 3.2
65
4.5
55
170
0.10
0.2
5.1
0.078 2.0 9-8208
100
40
125
3.18
0.125 3.2
65
4.5
55
170
0.30
0.2
5.1
0.135 3.4 9-8208
120
40
30
0.76
0.187 4.8
65
4.5
55
170
0.40
0.2
5.1
0.188 4.8 9-8208
124
40
20
0.51
0.187 4.8
65
4.5
55
170
0.60
0.2
5.1
0.25 6.4 9-8208
122
40
15
0.38
0.187 4.8
65
4.5
55
170
1.00
0.2
5.1
0.375 9.5 9-8208
126
40
10
0.25
0.187 4.8
65
4.5
55
170
NR
NR
NR
Type Torch: SL100 With Exposed Tip
Type Material: Aluminum
Type Plasma Gas: Air
Type Secondary Gas: Single Gas Torch
Thickness
Tip
Output
Amperage Speed (Per Minute)
Standoff
Plasma Gas Press
Flow (CFH)
Pierce
Pierce Height
Inches mm (Cat. No.) Volts(VDC) (Amps)
Inches
Meters
Inches mm
psi*
bar
Plasma Total** Delay (Sec) Inches mm
0.032 0.8 9-8208
110
40
440
11.18
0.187 4.8
65
4.5
55
170
0.00
0.2
5.1
0.051 1.3 9-8208
109
40
350
8.89
0.187 4.8
65
4.5
55
170
0.10
0.2
5.1
0.064 1.6 9-8208
112
40
250
6.35
0.187 4.8
65
4.5
55
170
0.10
0.2
5.1
0.079 2.0 9-8208
112
40
200
5.08
0.19 4.8
65
4.5
55
170
0.30
0.2
5.1
0.125 3.2 9-8208
118
40
100
2.54
0.19 4.8
65
4.5
55
170
0.40
0.2
5.1
0.188 4.8 9-8208
120
40
98
2.49
0.187 4.8
65
4.5
55
170
0.60
0.2
5.1
0.250 6.4 9-8208
123
40
50
1.27
0.187 4.8
65
4.5
55
170
1.00
0.2
5.1
0.375 9.5 9-8208
134
40
16
0.41
0.187 4.8
65
4.5
55
170
NR
NR
NR
Summary of Contents for CutMaster 40MM
