background image

                                                                                                      

 

1751 Hurd Drive ● Irving, Texas 75038 ● (972) 580-0200 ● (888) 580-0202 ● Fax (972) 580-0277 

URL:  www.thermal-edge.com ● Email:  

thermaledgeinfo@thermal-edge.com

 

SP-ENG-210-000-08 Rev 1.6          

24 

|

 

P a g e

                                                                                   

Warranty Information 
 

Thermal Edge products are warranted to be free of defects in workmanship, materials and components. 
The warranty period applies from date of shipment for one year.  

The above warranty applies when the equipment is operated under the following conditions:  

 

Ambient temperature not in excess of performance rating in normal atmosphere or as stated on 
product nameplate 

 

Voltage variation no greater than ± 10% from nameplate rating 

 

Frequency variation no greater than ± 3Hz from nameplate rating 

 

Maximum cooling load no higher than air conditioner namepla te rating 

 

Waiting five minutes before restarting air conditioner after intentional or accidental shutoff  

 

Compliance to all other installation, maintenance and oper ating instructions, as supplied 

Thermal Edge cannot assume responsibility for misapplication of its products or the erroneous selection of 
an inappropriate product by a non-authorized Thermal Edge representative. Our applications engineers 
will gladly assist in the selection of the proper product provided all required details of the application ar e 
furnished. 

Thermal Edge assumes no liability beyond the repair or replacement of its own product. This Warranty 
does not cover: 

 

Labor or reimbursement of labor for evaluation, removal, installation, repair, or cost of any 
warranted part, except at the Thermal Edge factory in Dallas, Texas 

 

Use of equipment for other than its designed purpose or operating conditions  

 

Operation in harsh, oily, corrosive or other abnormal environmental conditions, without the proper 
filtration, sealing, protective coatings and/or weather protection 

 

Damage to hermetic system resulting from continuous operation with dirty or clogged air filters or 
improper or negligent maintenance 

 

Use of refrigerant other than designated 

 

Customer modification or abuse 

 

Shipping damage or other accident 

 

Repair or service by unauthorized personnel. 

Cracked or broken hermetic tubing or brazed joints caused by shipping damage or mishandling are  not 
covered under the Warranty.  Claims for shipping damage are the responsibility of the Consignee. Timely 
claims must be filed with the freight carrier. 

The purchaser assumes the responsibility of grounding the unit and installing it in accordance with local 
electrical and safety codes, as well as the 2008 National Electric Code (NEC) and OSHA. 

THIS WARRANTY CONSTITUTES THE ENTIRE WARRANTY WITH RESPECT TO THE PRODUCT AND 
IS IN LIEU OF ALL OTHERS, EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF 
MERCHANTABILITY AND WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND IN NO 
EVENT IS THERMAL EDGE RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY NATURE 
WHATSOEVER. 

Summary of Contents for CS020 Series


























Reviews: