background image

 

 

                                     1                                                          Rev.2  07/26/98 

HALOGUARD

TM

 II/IR 

MULTI-GAS MULTI-SENSOR MONITOR 

INSTRUCTION MANUAL  

 

 

 

 

SE R IA L  N O .

M O D E L  N O .

Tem p. R ange

1 - = > 60

o

F

2 - = 40 - 60

o

F

3 - = < 40

o

F        

N o. of Sensors/G as Type

         

   A  - R -11

   B  - R -12
   C  - R -22 

               

O utputs

   D  - R -134a

1 - 4 x 3A  R elays

   E   - R -113

2 - 4 x 0 - 5 V D C

   F -  N H

3

                                 

or 0 - 10 V D C

   G  - R -123

   H  - O xygen

                          

O ptions/A ccessories

  A  - A udible A larm
  B  -  U PS

  C  - A uto C alibration
  E - Inlet/Exhaust Extension

  L - Strobe Light
  T - TW A  Integration

 

 

 

 

11285 Elkins Road Bldg. H-1 

Roswell, GA 30077 

TEL:  770-667-3865 

FAX: 770-667-3857 

www.thermalgas.com 

Distributed by:

Air-Met Scientific Pty Ltd

Work with Confidence

Air-Met Sales/Service

 

P: 1800 000 744 

F: 1800 000 774 

E: sales@airmet.com.au

Air-Met Rental

 

P: 1300 137 067 

E: hire@airmet.com.au 

W: www.airmet.com.au

Summary of Contents for HALOGUARD II/IR












Reviews: