background image

Bigwater 780e

CL-W0169

English

English

 

39

40

Q: How often do I have to refill the system?

A: Depending on the usage or surrounding environment,

     we strongly recommend checking the water level

     once a month to ensure optimal performance.

     If the liquid level is below the low level, please follow 

     the installation steps(P.21) to refill the coolant.

Q: How do I uninstall the liquid cooling system?

A : There are no special instruction when un-installing.  

      Please refer to installation and reverse the procedures.

Q: Can I add another liquid cooling upgrade kits on my 

     liquid cooling system?

A : Yes, there are numerous upgrades available for all 

      different components in PC.  

      Please visit www.thermaltake.com for more information.

Q: How do I know if the pump is working?

A: Place your hand on the pump.  

     If the pump is operating, the pump should vibrate gently.

Q: I'm running low on coolant. What's happening and 

     what can I do? 

A: The Performance Coolant included with main unit

     contains water based material so it is subject to natural evaporation. 

     It is normal for the coolant to decrease depending on the usage or 

     surrounding environment. For best performance, we highly 

     recommend replacing the coolant every 6 month.  

4.3  Liquid Cooling Q&A

Performing scheduled check up for the liquid cooling

 
system will ensure optimal cooling performance!

4.4  Schedule Maintenance

Ensure pump is working proper

.

Pump

Water Tank

Check for water level within the water tank

 we strongly recommend checking  the water level once a month

If the liquid level is 

below the low level, please follow the installation steps on manual  
to refill the coolant.
(

)  

Note: It is recommended that coolant to be replace once every 6 months. 
Depending on the workload of the system, coolant may need to be 
refilled more often.

Fan Assembly

.

 .۱

Check if LED is working properly

٢. Make sure fan controller is working properly.
٣. Make sure fan is operating properly without abnormal noise.

Summary of Contents for Bigwater 780e
























Reviews: