thermastor Quest 335 Installation, Operation And Maintenance Instructions Download

Page: 13 / 24

Fan

Pressing the Fan button alternates the unit between 3 fan speeds:

- (Hi)gh: Increased fan speed to be used exclusively in ducted applications. Deactivates flter-life compensation mode.

- (Au)to: Default fan speed. Filter-life compensation mode active.

- (Lo)w: Decreased fan speed that lowers the volume and performance of the unit. Deactivates flter-life compensation mode.

Filter-life compensation mode measures the static pressure increase due to the flter particulate build-up and increases fan speed to

maintain optimum airfow and performance.

Terminal Control

- When the Terminal Control button is pressed, the display will show “tc”.

- The Terminal Control button is used to activate the “DEHUM” input on the terminal block. (see section 5.1B)

- This must be activated when an external control is used to control RH. When Terminal Control is active, the internal RH sensor

is disabled.

5.1B Quest 335 External Control Options
Quest ofers two external control options

4028531

QUEST DEH 3000R CONTROL

WIRING DIAGRAM

24VAC

DMPR

COMP

FAN

DEHU

24V

FAN

COM

DEH

3000R

NOTE: 22 ga wire needed for sensor

4020175

HONEYWELL REMOTE HUMIDISTAT

WIRING DIAGRAM

DMPR

DEHU

24V

FAN

COM

Honeywell

Remote

Humidistat

Contact your dealer or call 1-877-420-1330 to order or go to www.questclimate.com/product-category/accessories.

Daisy Chain

QUEST 6 SERIES

UNIT#3

UNIT#2

UNIT#1

FLOAT

DEHU

24V

FAN

COM

24VAC

COMP

FAN

*NOTE DO NOT WIRE IN “FAN” TERMINAL WITH THIS APPLICATION

Summary of Contents for Quest 335

























Search results

Summary of Contents for Quest 335

Reviews:

Related manuals for Quest 335

Brands by name

Popular brands

thermastor Quest 335, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for Quest 335

Reviews:

Related manuals for Quest 335

Brands by name

Popular brands