background image

 

ECO ULTRA Electric Boiler 

Installation, Use and Care Manual 

(Revision June 2017)

, Page 

12.

 

3.6 SYSTEM SETUP 

Figures 2 to 8 indentify and show location of the 
different  components.  They  also  provide  typical 
heating system installation. External components 
location  may  vary  in  order  to  accommodate 
specific  installation  and  local  codes  and 
regulation. 

 
3.6.1 Connecting the boiler 

The boiler heating supply and return connections 
are  located  on  the  left  or  right  side    and  are 

1” 

NPTM  for  Model  50  and  1-

¼’’  NPTM  for  model 

70.  The  connections  at  the  left  or  right  can  be 
used.  The  important  thing  is  that  the  fluid 
circulation must be made from the bottom to the 
top (see figure 1) 
Unions are recommended on the inlet and outlet 
pipes  to  disconnect  the  water  heater  easily  for 
servicing if necessary. 
Dielectric  (insulating)  unions  should  be  used  if 
copper-steel connections are made.  
Insulate all pipes containing hot water, especially 
in unheated areas.  

 

3.6.2 Flow-check valve 

If  the  heating  system  uses  a  single  or  multiple 
circulators without motorized zone valves, 

a flow-

check  valve  must  be  installed

  to  avoid  all 

possibility  of  gravity  flow  and  heat  loss  during 
non-draw  periods.  Modern  circulators  are 
typically provided with spring loaded check valves 
that will provide adequate protection. 
If  the  heating  system  uses  motorized  zone 
valves, these will provide adequate protection.

 

 
3.6.3 Pressure relief valve 

The boiler is delivered with a factory installed tank 
pressure relief valve set at 207 kPa (30 psi).  

NEVER

  replace  the  pressure  relief  valve  by  a 

higher set pressure one.  
Connect  the  outlet  of  the  relief  valve  downward 
toward a safe location. 
Relief  valve  outlet  pipe  diameter must  not  be  of 
smaller diameter than the relief valve outlet. The 
oulet pipe end must be visible in order to observe 
any relief incident and be protected from freezing. 

NEVER cap or plug a pressure relief valve

 

outlet. The pressure relief valve is a safety 
apparatus and preventing its proper operation 
may cause death, injury or property damage. 
 

3.6.4 Expansion tank 

When operating the ECO ULTRA and the heating 
system,  pressure  will  vary  between  83  kPa  and 
193  kPa  (12  psi  to  28  psi).  The  operating 

pressure is affected by the type of heating system 
and the size of the expansion tank installed.  
The  expansion  tank  is  used  to  absorb  the 
increase of water volume from the boiler and the 
system when it is working. 
The  model  selection  should  be  based  on  the 
maximum  working  temperature  and  the  water 
volume  of  the  total  system.  For  example,  a 
system with radiators contains much more water 
volume than a baseboards system. Likewise, the 
ECO ULTRA also contains an important volume 
of water that has to be added : 
 
 

ECO ULTRA 50 : 48 usgal 

 

ECO ULTRA 70 : 71 usgal 

 
With this information, the installator or distributor 
should be able to make an appropriate selection 
for an expansion tank. 
 
Here  are  some  minimal  recommendations  for 
different types of heating systems. 
 

ECO ULTRA 

Baseboards 

Radiant 

floor 

Cast-iron 

radiators 

ECO ULTRA 50 

#30 

#30 

#60 

ECO ULTRA 70 

#60 

#60 

#90 

 
The expansion tank is generally installed on the 
wall or ceiling. It also has to be well supported. 
 

3.6.5 Water pressure regulator 

The boiler should be installed in such a way that 
it can automatically be fed with water in the event 
of a pressure drop.  
The  minimum  pressure  obtained  when  the 
system is cold is generally 12 psi (83 kPa). 
This  accessory  shall  be  equipped  with  one  or 
more check valves to avoid all possibilities of the 
boiler water returning to the potable water supply 
network (local regulation should be applied) 
 

3.6.6 Automatic Air Vent 

The  ECO  ULTRA  has  a  factory  installed  tank 
automatic air vent. This air vent function is to vent 
any air present in the tank. 
For proper operation, do not cap or block the air 
bleeder outlet. 
For proper operation of the heating system, it may 
be  necessary  to add  air  bleeders  to the  heating 
system circuits. 
 

Summary of Contents for ECO ULTRA 12









































Reviews: