background image

 

ECO ULTRA Electric Boiler 

Installation, Use and Care Manual 

(Revision June 2017)

, Page 

27.

 

-Some  heating  elements  are 
defective 
-The total capacity of the boiler is 
expelled 

to 

the 

heating 

distribution 

system 

at 

this 

temperature. 

-Replace defective elements 
-If a higher boiler water temperature is 
required to satisfy the heat demands of 
the  thermostats,  a  boiler  having  a 
larger capacity is required. 

Boiler stays in demand even when 
the thermostat is not in demand. 
(Systems with more than one 
thermostat) 
 

-On systems with electric zone 
valves, one or many end 
switches included in the valve is 
defective. 
-A jumper has been installed on 
terminals TT of the boiler 

-

Change defective “end switch”. 

 
 
 
-Make appropriate connections as 
shown in fig.7 

An overheated plastic odour  is 
released from the boiler 
 
 

Turn the power OFF to the boiler. 
Open the front and left side panel 
of the boiler. Check the 
components and electric wires 
for indications of overheating. 

Replace overheated components and 
check supply voltage to the boiler. 

Boiler safety valve is leaking 

-Pressure reading at the indicator 
shows a pressure above 28psi 
 
 
-Pressure is below 28psi 

-The pressure regulator on the 
distribution system is defective or the 
expansion tank is too small or 
defective. 
-Replace the safety valve 

 

Table 7: Resistance value of the outdoor sensor vs outdoor temperature

 

Temperature

 

Resistance

 

Temperature

 

Resistance

 

Temperature

 

Resistance

 

Temperature

 

Resistance

 

°F

 

°C

 

Ω

 

°F

 

°C

 

Ω

 

°F

 

°C

 

Ω

 

°F

 

°C

 

Ω

 

-50

 

-46

 

490,813

 

20

 

-7

 

46,218

 

90

 

32

 

7,334

 

160

 

71

 

1,689

 

-45

 

-43

 

405,71

 

25

 

-4

 

39,913

 

95

 

35

 

6,532

 

165

 

74

 

1,538

 

-40

 

-40

 

336,606

 

30

 

-1

 

34,558

 

100

 

38

 

5,826

 

170

 

77

 

1,403

 

-35

 

-37

 

280,279

 

35

 

2

 

29,996

 

105

 

41

 

5,21

 

175

 

79

 

1,281

 

-30

 

-34

 

234,196

 

40

 

4

 

26,099

 

110

 

43

 

4,665

 

180

 

82

 

1,172

 

-25

 

-32

 

196,358

 

45

 

7

 

22,763

 

115

 

46

 

4,184

 

185

 

85

 

1,073

 

-20

 

-29

 

165,18

 

50

 

10

 

19,9

 

120

 

49

 

3,76

 

190

 

88

 

983

 

-15

 

-26

 

139,402

 

55

 

13

 

17,436

 

125

 

52

 

3,383

 

195

 

91

 

903

 

-10

 

-23

 

118,018

 

60

 

16

 

15,311

 

130

 

54

 

3,05

 

200

 

93

 

829

 

-5

 

-21

 

100,221

 

65

 

18

 

13,474

 

135

 

57

 

2,754

 

205

 

96

 

763

 

0

 

-18

 

85,362

 

70

 

21

 

11,883

 

140

 

60

 

2,49

 

210

 

99

 

703

 

5

 

-15

 

72,918

 

75

 

24

 

10,501

 

145

 

63

 

2,255

 

215

 

102

 

648

 

10

 

-12

 

62,465

 

80

 

27

 

9,299

 

150

 

66

 

2,045

 

220

 

104

 

598

 

15

 

-9

 

53,658

 

85

 

29

 

8,25

 

155

 

68

 

1,857

 

225

 

107

 

553

 

Summary of Contents for ECO ULTRA 12









































Reviews: