background image

 

 

 

GAS FURNACE  

 

HIGHBOY AND COUNTERFLOW 

USERS INFORMATION MANUAL 

 

MODELS 

FOR USE WITH NATURAL GAS OR LP GAS (PROPANE) 

  CHB1-50 

  CDB1-50 

MHA1-50 

MDA1-50 

CHX1-75 CHB1-75 CDX 

1-75 CDB1-75 MHA1-75 MDA1-75 

CHX1-100 CHB1-100 CDX1-100 CDB1-100 MHA1-100 MDA1-100 
CHX1-125 CHB1-125 CDX1-125 CDB1-125 MHA1-125 MDA1-125

 

 

 

IF YOU DO NOT FOLLOW THE SAFETY PRECAUTIONS BELOW AND IN THIS MANUAL, A 

FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF 
LIFE. 

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE 
VICINITY OF THIS OR ANY OTHER APPLIANCE. 

 

WHAT TO DO IF YOU SMELL GAS: 

 

• 

DO NOT TRY TO LIGHT ANY APPLIANCE. 

• 

DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY PHONE IN YOUR BUILDING. 

• 

LEAVE THE BUILDING IMMEDIATELY. 

• 

IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE. FOLLOW THE GAS 
SUPPLIER’S INSTRUCTIONS. 

• 

IF YOU CANNOT REACH YOUR GAS SUPPLIER; CALL THE FIRE DEPARTMENT. 

 

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER, SERVICE 
AGENCY OR THE GAS SUPPLIER. (REFERRED TO IN THESE INSTRUCTIONS AS A QUALIFIED 
HEATING CONTRACTOR). 

 

PLEASE READ THESE INSTRUCTIONS PRIOR TO INITIAL FIRING, OPERATING THE FURNACE, AND 
BEFORE PERFORMING ANY MAINTENANCE. THESE INSTRUCTIONS MUST BE LEFT WITH THE 
HOMEOWNER AND SHOULD BE RETAINED FOR FUTURE REFERENCE BY THE HOMEOWNER/USER. 
 

 

 

 

 

 

 

 

 

 

 

 

 

 
THERMO PRODUCTS, LLC. 

    BOX 

217 

MG-1012    

NORTH JUDSON, IN 46366

 

ECN 4456-MA  

 

 

PHONE: (574) 896-2133   

 

MADE IN USA  

Summary of Contents for CDB1-100



















Reviews: