background image

All installations and services must be performed by qualified service personnel.

 

 

4

This page contains various warnings and cautions found throughout this manual. Please 
read and comply with the statements below. 

 

IF YOU DO NOT FOLLOW THE SAFETY PRECAUTIONS BELOW AND IN THIS MANUAL, A 

FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF 
LIFE. 

 

Property damage, personal injury, or loss of life could result from repair or service of 

this furnace by anyone other than a qualified heating contractor. Only the routine maintenance 
described in this manual may be performed by the user. 

 

To avoid injury from moving parts, shut off the power to the furnace before 

removing blower compartment door. 
 

Keep furnace free and clear of combustible materials, gasoline, and other flammable 

liquids and vapors. 

 

:

 Do not use this furnace if any part has been under water. Immediately call a qualified 

heating contractor to inspect the furnace and to replace any part of the control system and any gas 
control which has been under water. 

 

If you suspect there is a problem with the furnace, its venting system or any other 

related problem, immediately contact a qualified service agency. 

 

In the event your furnace fails to operate, do not attempt to put the furnace into  

operation. Contact a qualified heating contractor to service the furnace. 

 

A fire or explosion may result causing property damage, personal injury or loss of 

life if you do not follow these instructions exactly. 

 

Homeowners attempting maintenance other than that covered as homeowner/user 

maintenance may cause conditions which could result in personal injury or property damage. 
 

Shut off the power to the furnace before removing blower compartment door to avoid 

injury from moving parts. 

 

This furnace is not to be used for temporary heating of buildings or structures under 

construction. 
 

Call a qualified heating contractor to report suspected deficiencies (Do not attempt to 

make repairs yourself!) 

 
 
 
 
 
 

Summary of Contents for CDB1-100



















Reviews: