background image

35 

4)  This furnace is equipped with an electronic ignition system that automatically 

lights the burner. DO NOT try to light the burner by hand. 

  

5)  Turn on the electric power to the furnace at the disconnecting switch. 

   

6)  Adjust the room thermostat to the desired setpoint and set the operating mode, if 

equipped, to “HEAT”. 

  

7)  If the furnace will not operate, call a qualified heating contractor for service. 

 
TO INTERRUPT (STOP) OPERATION OF THIS FURNACE: 
 

1)  Adjust the room thermostat to the lowest setpoint and set the operating mode, if 

equipped, to “OFF”. 
  

2)  If service will be performed, turn off all electric power to the furnace at the 

disconnecting switch. 

 

3)  Turn the manual oil shutoff valve to the closed or “OFF” position. 

 
Oil Supply 

 

  If available, the use of ultra-low or low sulfur (less than 0.0015% S and 0.0015 - 

0.05%  S,  by  weight,  respectively),  no.  2  fuel  oil  is  highly  recommended.    Low 
sulfur fuel oil can help to significantly reduce instances of blockage and corrosion of 
the oil burner fuel delivery system, including the nozzle, the furnace heat exchanger, 
and the flue gas vent system. These benefits can appreciably decrease or eliminate 
service calls due to poor fuel quality. Air pollutants emitted by the furnace as well as 
the  typical  malodorous  smell  of  oil  combustion  will  also  be  reduced.  Consult  your 
fuel oil supplier about the availability of low-sulfur, fuel oil. 

 

  DO NOT allow the fuel tank to run completely dry during the heating season. If the 

fuel  tank  runs  completely  dry,  it  may  be  necessary  to  purge  the  oil  lines of  trapped 
air.  If  necessary,  contact  a  qualified  heating  contractor  to  bleed  the  oil  lines  and 
restart the burner.  

 

  During the warmer weather, keep the tank full to prevent condensation of moisture 

on the inside surface of the tank. The presence of moisture in the tank is beneficial 
to the growth of biological fuel contaminants (bacteria, mold, fungus, yeast, etc.). 

 

  Keep  the  cap  on  the  fuel  tank  fill  pipe  tightly  closed  at  all  times  to  prevent  the 

entrance of moisture, foreign matter, insects, etc. Consider adding a guard or filter to 
the tank vent pipe to reduce the entrance of water and foreign matter into the tank. 
Also,  check  the  tank,  vent,  and  fill  pipe  for  cracks  and  leaks.  Have  any  necessary 
tank repairs performed ASAP. 

 

Summary of Contents for VC-BBP Spirit Series





















































Reviews: