background image

2  |   Safety Considerations

Thermo Fisher Scientific ULT Freezers

Safety Considerations

In this manual, the following symbols and conventions are 
used:

Below are important safety precautions that apply to this 
product:

This symbol used alone indicates important 
operating instructions which reduce the risk of 
injury or poor performance of the unit.

CAUTION: 

This symbol, in the context of a 

CAUTION, indicates a potentially hazardous 
situation which if not avoided could result in 
minor to moderate injury or damage to the 
equipment.

WARNING: 

This symbol indicates potentially 

hazardous situations which, if not avoided, could 
result in serious injury or death.

WARNING: 

This symbol indicates situations 

where dangerous voltages exist and potential for 
electrical shock is present.

The snowflake symbol indicates extreme low 
temperatures and high risk of frostbite. Do not 
touch bare metal or samples with unprotected 
body parts.

This symbol indicates a need to use gloves during 
the indicated procedures. If performing 
decontamination procedures, use chemically 
resistant gloves. Use insulated gloves for handling 
samples and when using liquid nitrogen.

Before installing, using or maintaining this 
product, please be sure to read this manual and 
product warning labels carefully. Failure to follow 
these instructions may cause this product to 
malfunction, which could result in injury or 
damage.

Use this product only in the way described in the 
product literature and in this manual. Before using 
it, verify that this product is suitable for its 
intended use. If this equipment is used in a 
manner not specified by the manufacturer, the 
protection provided by the equipment may be 
impaired.

Do not modify system components, especially 
the controller. Use OEM exact replacement 
equipment or parts. Before use, confirm that the 
product has not been altered in any way.

WARNING: 

Your unit must be properly grounded 

in conformity with national and local electrical 
codes. Never connect the unit to overloaded 
power sources.

WARNING: 

Disconnect the unit from all power 

sources before cleaning, troubleshooting, or 
performing other maintenance on the product or 
its controls.

WARNING: 

“Caution, risk of fire”. This unit is 

charged with hydrocarbon refrigerants.

Summary of Contents for Forma FDE Series































Reviews: