www.thermo-varme.no
Side 2
washbasin, a swimming pool or other watering place.
•
In order to avoid overheating and fire hazard, do not cover or obstruct the
appliance. Do not put any of the following materials on the appliance, such
as clothes, blanket, pillow, paper etc. The minimum distance 1M between
the appliance and flammable materials must always be maintained.
•
The casing and the front cover of the appliance become extremely hot
during operation. Pay attention that, no combustible material due to Wind or
other environmental influences covers or obstructs the appliance, such as
curtains, marquees, flags, plastic foil etc. Do not touch the appliance.
Caution! Risk of scald injury!
•
Do not let the cord hang over edge of table or counter, or touch hot surfaces.
•
If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person in order to avoid a hazard.
•
Operation of the appliance must be discontinued and remove the mains plug
immediately, if improper use produces cracks, breaks or flaws on the
aluminium casing, on the front cover surface or on the cord or plug, with the
result that there is a risk of electrical shock and/or fire hazard.
•
Do not try to repair the appliance by your-self. Please contact with the
service agent or a suitably qualified electrician for maintenance.
•
Remove the plug from the power outlet and wait untill the appliance is
sufficiently cooled off before cleaning.
•
Do not store any burnable liquids, paint, gas tank etc. in the immediate
surroundings of the appliance.
•
Do not use the appliance in flammable ambience(such as near by
combustible gas or spray cans)! Danger of explosion and fire!
•
This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
•
Keep out of reach of children. In order to keep children from the dangers of
electrical appliances, never leave them unsupervised with the machine.
Consequently, when selecting the location for your machine, do so in such a
way that children do not have access to the machine. Children being
supervised not to play with the appliance.
•
Caution! Never leave the appliance unsupervised when in use. Do not use
the appliance with a programmer, timer or any other device that switches
the appliance on automatically.
•
To avoid hazards, do not use the appliance with an external voltage
regulator(such as dimmer, speed controler etc.)
www.thermo-varme.no
Side 3
•
The appliance must only be mounted by an authorised specialist, paying
attention to the relevant regulations of the power supply companies and the
regional construction regulations.
Installation
For additional protection the installation of a residual current device (RCD) is
advisable.
1.
Remove all package material and check the appliance, supply cord and
the plug for signs of damage.
2.
Pay attention to the mounting place and all mounting material(dowels,
screws). Ensure they are suitable and stable enough for mounting and
lastingly holding of the appliance.
3.
Before mounting, the minimum safe mounting distances and tilt angles
shown in the figures must be strictly followed.
The distance between the bottom edge of the appliance and the floor must
be at least 2.5 M.
There must be a distance of at least 0.5 M between the appliance and the
cellings, roofs or other covers. If the covers are consist of flammable
material, such as wooden cellings, wooden roofs etc., the distance at least 1
M must always be maintained.
There must be a distance of at least 1.5 M at each side between the
appliance and walls or the like. See figure 3.
The max. degree to horizontal is 60°and the min. degree is 40°. See figure
4.
The infrared heater could also be swung from left to right. The max. swing
degree is 25°
4.
Pay attention that, the installation of the appliace must not add
excessive wind load.
5.
Fix the mounting bracket on the wall first. Ensure that the place to be
installed is secure and firm.
6.
Assemble the appliance onto the mounting bracket.
7.
Adjust the desired angle of radiation and fest screw all screws.
Check regularly the screws’ connection. Mechanical bearing pressure
and oscillation due to wind or rain could lead to loose.
8.
Plug in the power source. And then observe, whether during the first
10-15 Minutes the appliance works trouble-free.
