background image

 

                                                     

Page 10 

Note:

 

 
 

It is not advisable

 that this PTFE cover material be used when the 

press is being used for transfer printing. 

 

 
 
3.4 

Pressing Pad Assembly 

 
 
 

 

The pressing pad

 normally supplied with this machine is silicone rubber.  

The pressing pad must be maintained in good condition at all times and 
replaced when showing signs of wear.  A worn pressing pad will always 
affect the quality of printing/fusing.  Do not insert items into the machine 
which would tend to cut the pressing pad, i.e. buttons, pins, press studs or 
zips. 
 

Never allow

 the hot heat plate to rest on the pressing pad when the press is 

not being used as the pad may be damaged. 
 

IMPORTANT NOTE:

 

 

The pressing pad

 supplied with the machine is of the correct thickness.  

Using a thicker pad may invalidate your warranty. 
 

 
3.5 

Shutting Down 

 
 
 

To shut down the machine

, turn off the green illuminated rocker switch to 

the right of the controller.  The handle should be in the up position. 
 

After shutting off the machine

, it should not be switched on again for 30 

seconds. 
 
 

3.6 

Fault Diagnosis 

 
 
 

This machine

 has a built in fault diagnosis.  The display may show the 

following: 
 

1. 

Heat Fault

 

 
 

If the element

 of the heat press, or the thermal cut-out go open 

circuit, after approximately 20 minutes the display will show “Heat 
Fault”.  If this display is seen, contact your machine supplier 
immediately. 

 
 
2. 

Probe Fault

 

 
 

If the probe

 goes open circuit, the display will show “Probe Fault” 

immediately.  Contact your machine supplier immediately. 

 

Summary of Contents for Almere NL-22




























Reviews: