background image

 

                                                     

Page 5 

Safety Tips (cont.) 

 
 

 

MACHINE FUSES

 - type: ultra rapid (FF) fuses 1¼” 230 Vac 

max. 3.15 amps.  (120 Vac max.  6.3 amps). 

 
 

 

WARNING - 

THIS APPARATUS MUST BE 

EARTHED (GROUNDED)

 

 

 

 

CAUTION 

 

This machine gets hot whilst operating.  Take care not to touch any 
surfaces that are labelled “Caution this plate is HOT”. 

 
 

 

MACHINE OPERATION 

 

Only suitably trained personnel should operate this machine. 
 
For Safety 

use both handles to move the handle up and down.

 

 

Do not

 allow the handle to move upward, by the effect of the 

springs, without a hand on it 

 
Keep fingers away from 

trapping points

 in the arm - lever toggle 

mechanism. Using both hands on the handle keeps the hands safe. 

 

Contact

 your print media suppliers to ascertain whether 

fumes

 are 

given off during the transfer process, and if so what precautions are 
needed for operator safety. These may include 

air extraction

 and / 

or masks for personnel. 

 
 

Please refer to Appendix I for an illustration of the NL-22 press 
machine. 

  
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

Summary of Contents for Almere NL-22




























Reviews: