pg. 10
5.4 OPERA
5.4 OPERA
5.4 OPERA
5.4 OPERA
5.4 OPERATING LEVEL SETTING
TING LEVEL SETTING
TING LEVEL SETTING
TING LEVEL SETTING
TING LEVEL SETTING
The heater must be fed with the rear switch in position "1". Display (7) may show the inscriptions On , OFF or Start. ".
Your appliance is delivered with an excellent program installed that favours combustion yield; the program is called P 1.
If you are using pellets with an out-of-standard incidence of residues after combustion in the brazier, alternative levels may be selected:
P 2 :
this program increases the smoke suction unit speed acceleration.
(program P2 increases air delivery to the burner which promotes the combustion of tightly compacted pellets: this program reduces
combustion efficiency).
P 0 :
when using too long pellets and/or flue outlets with very high vacuum, over 2 mm water column.
The pellet consumption value is not affected by the operating level settings.
Select the required level by acting as follows:
Repeatedly press three times the key (6) until the inscription LIV flashes on the display and, then, the corresponding level set on the heater
will show ( P1 o P2 o P0) In order to change the operating level as key (4) is kept pressed, press the key (3).
By holding down button (4) and pressing button (3) repeatedly the level changes in the following sequence: P2... ...P0 ... P1.
If the change is made while the insert is running the difference in the flame will be apparent. It is mandatory to pay
particular care when selecting the most appropriate operating cycle for your installation. After the selection of the
operating cycle a thorough cleaning of the brazier is mandatory.
For an overall confirmation and to return to the status display of the heater, repeatedly press the key (6) until the operating status is
displayed.
When the programming is enabled (temporary inscription on cr on the display and, at the same time, a fixed point is present on the
right side at the bottom of the display) any additional chronothermostat (see para. 7.2) is deactivated.
1
2
3
4
5
6
7
8
9
10
6
6
6
6
6
USE OF
USE OF
USE OF
USE OF
USE OF THE HEA
THE HEA
THE HEA
THE HEA
THE HEATER
TER
TER
TER
TER
6 . 1
6 . 1
6 . 1
6 . 1
6 . 1
5 . 1
5 . 1
5 . 1
5 . 1
5 . 1 SWIT
SWIT
SWIT
SWIT
SWITCHING ON
CHING ON
CHING ON
CHING ON
CHING ON THE HEA
THE HEA
THE HEA
THE HEA
THE HEAT E R
T E R
T E R
T E R
T E R
Before using the appliance check that all the movable parts are in place; also remove any labels and stickers from the glass to avoid having
permanent traces remain on the surfaces.
Turn the switch installed on the back of the heater to position "1" (= ON). Press button (1) to start the start up phase. When key (1) is
repeatedly pressed, the desired combustion level can be set and it will be active at the end of the ignition stage.
The electrical heater will start to overheat and after a few minutes the first lot of pellets will start dropping into the brazier. This occurs
because the screw feeder has to fill up because it is completely empty. The first time the heater is started up the start up phase will have to
be carried out twice for this very reason.
CAUTION : The start up phase (word Start appearing on the display) takes 20 minutes during which the heater ignores any
commands transmitted to it. After this time has elapsed the word ON appears on the display. The fan starts as soon as the heater
body exceeds 42°C. During the work stage it is then possible to adjust combustion and the ventilation:
Combustion is adjusted by 5 leds (through key (1)) , while the ventilation adjustment is distributed over 6 levels shown by the leds
that turn on in succession (through key (2)).
To turn the heater on it is necessary for the inscription OFF to be present on the display; if it is not present, the key (6) must be
repeatedly pressed until the inscription OFF appears.
The heating capacity is adjusted by pressing key (1) or on the remote control provided . Act on this command to adjust the quantity of pellets
fed to the firebox. Maximum combustion power is achieved when all 5 leds are lit.
Caution: The fan starts as soon as the heater body exceeds 42°C. The fan setting is expressed visually by means of 6 different
positions represented by 6 bars: press button (2) repeatedly to regulate it.
A slight vibration of the heater is quite normal when it is running.
6.2 HEA
6.2 HEA
6.2 HEA
6.2 HEA
6.2 HEATER COMB
TER COMB
TER COMB
TER COMB
TER COMBUSTION
USTION
USTION
USTION
USTION AND
AND
AND
AND
AND VENTILA
VENTILA
VENTILA
VENTILA
VENTILATION
TION
TION
TION
TION ADJUSTMENTS
ADJUSTMENTS
ADJUSTMENTS
ADJUSTMENTS
ADJUSTMENTS
Summary of Contents for ECOTHERM 5000
Page 16: ...pg 16 ...
Page 17: ...pg 17 ...
