pg. 12
ECONOMY program
In the ECONOMY program the heater always operates at the minimum combustion level and the minimum ventilation level. You cannot use the
infrared control with this program .
CAUTION: THE HEATER MUST ALWAYS BE SWITCHED ON AND OFF FROM THE CONTROL PANEL LOCATED ON THE HEATER.
FOR THE RADIO CONTROL TO WORK THERE MUST NOT BE AN ACTIVE PROGRAM SET ON THE CONTROL PANEL LOCATED
ON THE HEATER OR AN EXTERNAL ROOM TEMPERATURE THERMOSTAT OR AN EXTERNAL CHRONOTHERMOSTAT.
6.4.2 TRANSMISSION CODES SETTINGS.
6.4.2 TRANSMISSION CODES SETTINGS.
6.4.2 TRANSMISSION CODES SETTINGS.
6.4.2 TRANSMISSION CODES SETTINGS.
6.4.2 TRANSMISSION CODES SETTINGS.
Before beginning any maintenance operation ensure that the appliance is in the OFF phase and disconnect it from the electric power outlet.
If several heaters are installed in close locations it may be necessary to set different transmission codes. The change of code must be made
both on the motherboard inserted in the heater (see figure below left ), and in the radio control (see figure below left). Position the switch 0-1
(located on the back of the heater) on 0. To access the board you need to remove the heater's right side panel as described in the dedicated
paragraph and remove the board cover by undoing the two screws as indicated in the figure below on the right.
The codes must be identical, and for this purpose you could use the numbers marked on the microswitches as reference. Firstly set the new
code on the motherboard, next set the new code on the remote control and then switch the remote control on and off with the switch (11)
located on the back of the remote control.
AUTO 5 program
In program AUTO 5 the room temperature thermostat is enabled. The radio control adjusts the ventilation and the combustion automatically in
relation to the target room temperature set in display area (8).
The desired room temperature appears in area (8).
You can vary the desired
room temperature by simply pressing button (3) and/or (4) (variation indicated in area (8)). The remote control will set the maximum
combustion and ventilation levels and modulate them both as the room temperature (5) approaches the target temperature (8). When the
target temperature (8) in the room (5) is reached, the combustion level will stabilise on a bar as will the ventilation level. Caution: it is possible
that, due to radio interference, the commands sent to the heater will not be implemented. You cannot use the infrared control with this
program.
Caution: the power and the ventilation depend on the preset value, if the required temperature is too high or not reachable the
heater could operate at maximum power for long periods of time.
PALMARE G
ESTITO
VIA O
NDE RADIO
SELETTO
RE CO
DICI PER RADIO
CO
MANDO
3
2
1
ON
4
4
1
ON
3
2
2
1 3
4
5
6
PER RADIOCOMANDO
SELETTORE CODICI
4
3
ON
2
1
4
3
ON
2
1
AUTO 3 program
In program AUTO 3 the room temperature thermostat is enabled . The remote control adjusts the ventilation and combustion automatically in
relation to the target room temperature set in display area (8).
The desired room temperature is displayed in area (8).
You can vary the
desired room temperature by simply pressing button (3) and/or (4) (variation indicated in area (8)). The remote control will set the
combustion power at level 3 and the ventilation at level 4 and modulate them both as the room temperature (5) approaches the target tempe-
rature (8). When the target temperature (8) in the room (5) the combustion level will stabilise on a bar as will the ventilation level. Caution: it is
possible that, due to radio interference, the commands sent to the heater are not acknowledged???implemented. You cannot use the infrared
control with this program .
Caution: the power and the ventilation depend on the preset value, if the required temperature is too high or not
reachable the heater could operate at maximum power for long periods of time.
Caution: ensure correct and equivalent position of
the microswitches.
K E Y
code selector for handheld radio control
radio wave-controlled code selector for
handheld radio control
LEGENDA
selettore codici per radiocomando
selettore codici per radiocomando
palmare gestito via onde radio
Summary of Contents for ECOTHERM 5000
Page 16: ...pg 16 ...
Page 17: ...pg 17 ...
