pg. 6
4
4
4
4
4
INST
INST
INST
INST
INSTALLA
ALLA
ALLA
ALLA
ALLATION
TION
TION
TION
TION
4 . 1
4 . 1
4 . 1
4 . 1
4 . 1
HEA
HEA
HEA
HEA
HEATER L
TER L
TER L
TER L
TER LOCA
OCA
OCA
OCA
OCATION
TION
TION
TION
TION
CAUTION : Always use trolleys to move the appliance and the appliance must
always be in a vertical position. Follow the general guidelines set out in paragraph
1.1 to the letter. Keep in mind that the flooring of the room in which the heater is to
be installed must withstand the combined weight of the appliance and the pellets
contained in the tank.
CAUTION: The room in which the appliance will operate must be adequately ventilated
(minimum air intake 1300 m3/h). The appliance must be positioned at a minimum
safe distance from walls and furnishings. This distance will have to be increased
considerably if the objects surrounding the appliance are inflammable
(matchboarding, furniture, curtains, picture frames, sofas, etc...). The recommended
minimum distances are illustrated in the drawing below on the right. Installation in
the vicinity of heat-sensitive materials is only permitted if suitable insulating protection
is placed between the object and the appliance (ref. Uni 10683). Adjust the mounting
feet to obtain a slight gap between heater and flooring to ensure that the heater is
not resting directly on the floor. It is advisable to interpose a floor protector plate
between the heater and the floor if the latter is made of wood or other combustible
material.
4 . 1 . 1
4 . 1 . 1
4 . 1 . 1
4 . 1 . 1
4 . 1 . 1
INST
INST
INST
INST
INSTALLA
ALLA
ALLA
ALLA
ALLATION OF MET
TION OF MET
TION OF MET
TION OF MET
TION OF META L
A L
A L
A L
A LCOL
COL
COL
COL
COLOR CASING
OR CASING
OR CASING
OR CASING
OR CASING
Once the heater has been positioned the next step is to install the side panels
and the top ceramic panel as shown in the image below on the left. Carry out
the following operations:
- Unscrew and remove the 2 knobs (H).
- Remove the cover (I).
- Now insert the side panel (M)'; position the bottom holes on the folds in the
base and fix the 2 top screws (Figure 1).
- Next remount the complete cover (I) and the top ceramic panel (L) and
screw back on the 2 knobs (H) removed earlier.
- Fix the lower front ceramic panel to its support with the silicone provided;
degrease and clean the ceramic panel support before gluing the parts to
ensure optimal adhesion. Leave the ceramic panel in the position illustrated in
Figure 2 and wait 24 hours before handling it.
- Next fasten the lower ceramic panel to the heater following the instructions
in Figure 3 .
Remember that the heater must be completely cooled down before the side
panel can be cleaned with a soft cloth and water.
The casing on the easy model is factory-mounted before delivery .
45
0
m
m
SE
M
AT
ER
IA
LE
C
OM
BU
ST
IB
ILE
45
0
m
m
SE
M
AT
ER
IA
LE
C
OM
BU
ST
IB
ILE
ISOLANTE TERMICO
200 m
m SE
MAT
ERIAL
E CO
MBUS
TIBILE
200 mm SE MATERIALE
COMBUSTIBILE
Tee ispezionabile
H
H
I
L
M
Fig ura 1
Figura 2
Figura 3
Key
200 / 450 mm if combustible material
Heat insulating material
Inspectable Tee element
Figure
LEGENDA
200 / 450 mm se materiale combustibile
Isolante termico
Tee ispezionabile
Figura
Summary of Contents for ECOTHERM 5000
Page 16: ...pg 16 ...
Page 17: ...pg 17 ...