Page 16
lation, use and maintenance guide
LEVEL 2: this program increases the smoke suction unit speed acceleration (program Level 2 increases air delivery to the burner
which promotes the combustion of tightly compacted pellets: this program reduces combustion efficiency).
LEVEL 0: when using too long pellets and/or flue outlets with very high vacuum, over 2 Pascal. When operating at LEVEL 0 the
burner becomes dirty very easily. The pellet consumption value is not affected by the operating level settings. Select the required
level by acting as follows:
press button (6) three times until the word LEVEL appears on the display after which the level set will appear (LEVEL 1 or LEVEL 2
or LEVEL 0). In order to change the operating level as key (3) is kept pressed, press the key (4). By holding down button (3) and
pressing button (4) repeatedly the level changes in the following sequence: LEVEL 2... ...LEVEL 0 ... LEVEL 1.
If the change is made while the appliance is running the difference in the flame will be apparent. It is
mandatory to pay particular care when selecting the most appropriate operating cycle for your
installation. After the selection of the operating cycle a thorough cleaning of the brazier is mandatory.
For the entire procedure to be confirmed and to move back to the appliance status display, key (6) must
be repeatedly pressed.
6 – USE OF THE APPLIANCE
Your appliance has obtained the CE marking and has been made to run for 1 hour to check that it functions correctly. It has also
undergone numerous tests as detailed in the test check sheet supplied with the generator. The product must not be used by
children, by persons with physical or mental impairments, by persons who are not familiar with the instructions for use and
maintenance of the product (the instructions are found in this booklet). CAUTION: Before each use make sure that the burner is
clean and positioned correctly in its lodging, check that the ash pans are clean and shut tight and check that the firebox door is
locked. WARNING: the door must always remain shut tight when the heater is operating. It is strictly forbidden to open the door
while the appliance is in operation. While the appliance is in operation the smoke exhaust pipes and the appliance itself can reach
extremely high temperatures: do not touch them! Do not expose your body to hot air for long, do not overheat the room in which the
appliance is installed, as these actions could cause health problems. Do not expose plants or animals directly to the hot air flow as
this could have noxious effects on them. It is strictly forbidden to use any type of fuel (liquid, solid...) to light the appliance : the
appliance must light up automatically as designed and described in this installation, use and maintenance booklet; in this regard, it
is strictly prohibited to pour pellets (or other material) directly into the brazier. Do not place non-heat resistant or inflammable or
combustible objects in the vicinity of the appliance: keep them at a suitable distance. Do not place wet clothing to dry on the
appliance.
When using a clothes horse, keep at a suitable distance. It is strictly prohibited to disconnect the appliance from the electrical
power mains while it is in operation.
6.1 SWITCHING ON THE APPLIANCE
Before using the appliance check that all the movable parts are in place; also remove any labels and stickers from the glass to
avoid having permanent traces remain on the surfaces. Always ensure that the brazier is clean and seated correctly in its lodging
(see para. 8).
Turn the switch installed on the back of the appliance to position "1" (= ON). Press button (1) to start the start up phase.When key
(1) is repeatedly pressed, the desired combustion level can be set and it will be active at the end of the ignition stage. The electrical
heater will start to overheat and after a few minutes the first lot of pellets will start dropping into the brazier. This occurs because the
screw feeder has to fill up because it is completely empty. The first time the appliance is started up the start up phase will have to
be carried out twice for this very reason.
CAUTION: The start up phase (the word START appearing on the display) continues until the word
START .remains lit.Once this phase has ended the word WORK appears on the display. The fan will
begin operating as soon as the combustion smoke reaches a suitable temperature. During the work
stage it is then possible to adjust combustion and the ventilation:
The combustion can be adjusted by 5 bars through button (1)), the ventilation setting can be set on 6 levels indicated by the
sequential lighting up of the corresponding bars on the display (through button (2)).
To turn the appliance on it is necessary for the inscription OFF to be present on the display: if it is not present, the key
(6) must be repeatedly pressed until the inscription OFFappears.
