background image

13

• Plated wire grates:

 Wash grates with concentrated grill 

cleaner or use soap and water solution. Dry thoroughly and 
store indoors between cookouts. 

• Stainless steel surfaces: 

To maintain your grill’s high quality 

appearance, wash with mild detergent and warm soapy water 
and wipe dry with a soft cloth after each use. Baked-on grease 
deposits may require the use of an abrasive plastic cleaning 
pad. Use only in direction of brushed finish to avoid damage. 
Do not use abrasive pad on areas with graphics.

• Cooking surfaces:

 If a bristle brush is used to clean any of

the grill cooking surfaces, ensure no loose bristles remain on
cooking surfaces prior to grilling. It is not recommended to
clean cooking surfaces while grill is hot.

Storing Your Grill

• Clean cooking grates.
• Store in dry location.
• When LP cylinder is connected to grill, store outdoors in a well-

ventilated space and out of reach of children.

• Cover grill if stored outdoors. Choose from a variety of grill 

covers offered by manufacturer.

• Store grill indoors ONLY if LP cylinder is turned off and 

disconnected, removed from grill and stored outdoors.

• When removing grill from storage, follow “

Cleaning the Burner 

Assembly

” instructions before starting grill.

Cleaning the Burner Assembly

Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1. 

Turn gas OFF at control knobs and LP cylinder.

2.

heat tent 

3.

4.

5.

6.

7.

VERY IMPORTANT: Burner tubes must re-engage valve
openings. See illustration (A).

8.

electrode

9.

heat tent

grease cup

10.

Remove cooking grate and 

.

Under grill remove grease cup, disconnect ignitor wire from 
burner. 
Inside grill remove burner assembly (A), clean ceramic 
portion of electrode with rubbing alcohol and a swab.
Clean outside of burner with soap and water. Lay burner 
upside down on flat surface, insert garden hose to force 
water through tubes. Make sure water comes out of all 
burner holes. Open clogged holes with a thin wire. Shake 
out excess water and examine holes. Due to normal wear 
and corrosion some holes may become enlarged. If any 
large cracks or holes are found replace burner.
If grill is to be stored, coat burner lightly with cooking oil. 
Wrap in protective cover to keep insects out.
If not storing grill after cleaning, replace burner into grill 
bottom.

Reattach ignitor wire to 

.

Reposition 

 and cooking grate. Reattach clean 

 to grease clip.

Before cooking again on grill, perform a 

“Leak Test” 

and 

“Burner Flame Check”

.

A

Valve

Correct burner-to-valve engagement

Burner Tube

B

Check that the burners are not damaged. Because of 
normal wear and corrosion some holes may have 
enlarged. If you notice large cracks or large holes, 
replace the burner.

11.

CAUTION

SPIDER ALERT!

SPIDER AND WEBS

INSIDE BURNER 

If your barbeque is getting hard to light or 
the flame is weak, check and clean the 
venturis and burners.

Summary of Contents for Thermos C-21G0 461611513

































Reviews: