Press the
SETUP
button twice to return to the
SETUP
/
INPUT
page 1
sub menu, or 4 times to return to the main
INPUT SELECT
menu.
VFD Brightness
Each
INPUT SELECT
button can have a different VFD brightness assigned to it. From the Input Select menu, press
SETUP
,
ACTIVE
INPUT SETTINGS
, then
VFD BRIGHTNESS
(button #
6
). This allows the user to change the
default brightness value. The range is from
OFF
to
FULL
(brightest), in four steps. Any changes made to this
parameter are reflected the next time that
INPUT SELECT
button is pressed. If this value is set to
OFF
, pressing
any button except
DISPLAY
will automatically brighten the VFD to its maximum level. If the next button pressed is
not another
INPUT SELECT
or function button then the VFD will revert back to its default brightness in
X
seconds.
X
represents the
TIME
parameter value in the
SETUP
/
ACTIVE INPUT SETTINGS
page 1
/
OSD
sub menu. If the VFD
is on but not set to
FULL
, pressing any button other than another
INPUT SELECT
button will allow the VFD to
remain at its default brightness, with the exception of pressing the
DISPLAY
button which will always override the
default VFD brightness setting. The VFD override takes precedent.
Setup Input Page 2
To access this page, from either
INPUT SELECT
page or any other
function menu, press
SETUP
then
ACTIVE INPUT SETTINGS
, then
the
A-D
button once. Page 2 of the
SETUP
/
ACTIVE
INPUT
SETTINGS
menu is shown in figure 90.
Figure 90 - Video Display of the
SETUP
/
INPUT Page 2 Sub Menu
LFE Phase
The
LFE PHASE
can be changed from
+
(in phase) to
–
(180 degrees out of phase). This can be edited via button #
1
.
Mapping a Source (Input Jack to INPUT SELECT button)
Pressing button #
2
accesses 2 sub menus that allow the user to assign which input jacks will be mapped to the
currently selected
INPUT SELECT
button, both audio and video. There is one page for audio jack mapping and one
for the combined composite/multi format and S-video. Up to six audio and six video input jacks can be mapped to
any one
INPUT
SELECT
button, and the order that they are mapped determines the search order when pressing the
A-D
button in either
INPUT SELECT
menu.
Please refer to page 60 for additional information and examples of mapping input jacks to
INPUT SELECT
buttons.
91
Summary of Contents for Casablanca III
