28
Dolby Digital, DTS Setup
The center and left/right surround speaker levels and delays can be different for Dolby Digital and DTS sources. There
are separate
SETUP
submenus designed just for these modes. When the mode is Dolby Digital or DTS, the center and
surround delays will work together with changes made in the above
DLYS
submenu. The values of the levels set in the
Dolby Digital and DTS Setup submenus will be added to (or subtracted from) the level values in the
SETUP
/
INP
/
LVLS
submenu.
12)
a) Play a Dolby Digital 5.1 movie.
b) Go to the Dolby Digital setup submenu – page 2.
c) If desired, set the center speaker delay.
d) If desired, set the surround delay.
e) Set the center speaker level and the surround speaker level to 0. Please refer to the
SETUP/Dolby Digital
section in this manual for additional information regarding setting the Dolby Digital center and surround levels.
f) If the incoming signal is 5.1 and the Surround Back channels are being used, set the
+SPKR
value to the
process which will be used to create the additional channels. This decision will be made solely by listening
to which sounds best to the user.
g) Go to the Dolby Digital setup submenu – page 3.
h) If the incoming signal is EX flagged and the Surround Back channels are being used, set the
+SPKR
value
to the process which will be used to create the additional channels. This decision will be made solely by
listening to which sounds best to the user.
Remember that these values will be in effect only when the
MODE
is Dolby Digital and specific flags are present.
13)
a) Play a DTS encoded CD or movie.
b) Go to the DTS page 1 Setup submenu.
c) If desired, set the center speaker delay.
d) If desired, set the surround delays.
e) Set the center speaker level.
f) Set each surround speaker.
g) Set the
LFE
level at
0
for DTS movies, or
-10
for DTS music. (The user can choose to use two separate
input select buttons, one for DTS movies and one for DTS music, all parameter values being the same except
for the LFE setting).
h) If the incoming signal is 5.1 and the Surround Back channels are being used, set the
+SPKR
value to the
process which will be used to create the additional channels. This decision will be made solely by listening
to which sounds best to the user.
These parameter values apply only when the
MODE
is
DTS
.
Remaining Setup
14) Now that the speaker configuration, crossovers, levels and delays have been set up for input select button #1, they
should be copied to all input select buttons as a good starting point. Do this in the
MACROS
submenu when input
select #
1
is the current input.
15) Each input select button has a default mode assigned to it. (To see the Default Modes, please see page 22.) The
default mode for a given input select button is set and stored in the first
SETUP
/
INPUT
page. As the user scrolls
through the list of modes, there are 2 positions in this list that are not currently used. In these positions, the word
SKIP
will be displayed.
a) Press input select button #1.
b) Go to the
SETUP/INP
– page 1 submenu.
c) Set the applicable default
MODE
.
d) Repeat steps b and c for each input select button.
16) An input signal is “processed” a certain way depending on which
MODE
is currently selected
17) The audio
SOURCE
pages allow the user to map up to three audio sources to the currently selected input. It is
recommended that all other displayed jacks in this submenu be cleared if they are not to be used. Please refer the
Mapping Jacks
and
Search Order
sections of this manual for additional details about mapping input jacks to a given
Input Select button.
Verify that the desired rear panel audio input jacks are properly mapped to each Input Select button that is to be
used.
a) Select input # 1.
b) Go to the AUDIO
SOURCE
submenu.
Summary of Contents for Casablanca IV
