82
STATUS Display
This display, accessible from the hand held remote and viewed on the VFD, provides the user with a ‘quick view’
of the most pertinent current settings of the Casablanca IV as well as information about a Dolby Digital source.
The status page is available from any menu or submenu simply by pressing the
STATUS
button.
When the
STATUS
display is activated, its title is displayed in the upper left corner along with the following:
•
The current
INPUT SELECT BUTTON NAME
.
•
The current mapped input jack.
•
The
MODE
.
•
The
TAPE OUT
audio
source.
•
The
PHASE
parameter value (
0
°
or
180
°
)
•
The Sample
rate (
S RATE
) of the currently selected source.
•
The
MASTER VOLUME
level.
Press the
A-D
button once to display the status of the current Dolby Digital source. Press
A-D
once more to
display the status of the current DTS source.
Note that a Dolby Digital or DTS source needs to be playing in order to display the correct values on these status
pages.
Please refer to page 78 for additional information pertaining to Dolby Digital Status menu and page 79 for the DTS
Status menu.
Pressing the
STATUS
button once will clear the status display. Pressing a function button will clear the status
display and show that menu.
MODE Function
This function allows the user to audition
MODE
s for the currently selected input. Storing a default
MODE
is
done in the
SETUP
/
INPUT
page 1
submenu.
Pressing the
MODE
button once displays the first page of the
MODE
menu. This page consists of 6 different
signal processing modes, one of which can be selected and temporarily applied to the current input.
Please refer to page 62 for additional information regarding Dolby Digital options, page 65 for additional
information regarding DTS.
* * *
After selecting a temporary mode for the current input, press the
MODE
button once more to clear the video
monitor. The
MASTER VOLUME
can be controlled using the
LEVEL
UP
/
DOWN
buttons in these 3 menus.
Default Mode
Each
INPUT SELECT
button can have a different default
MODE
assigned to it. To assign a default
MODE
for
a given
INPUT SELECT
button, first press the applicable
INPUT SELECT
button,
SETUP
,
INPUT
then button #
4
(
MODE
). Use the
LEVEL UP/DOWN
buttons to edit this parameter and select the desired default
MODE
.
Press
SETUP
twice to exit. Repeat this procedure for each
INPUT SELECT
button.
Note
: Pressing the front panel
MODE
function button allows the user to audition different modes for a given
source, when applicable, however changing modes via the
MODE
button does not store a mode selection.
Summary of Contents for Casablanca IV
