background image

Installation Manual  

9

Controls:

-

Touch and release the ON/OFF [1] button to turn the refrigerator on.(ART02735)

- If the indicator light, below the button, glows solid blue, it means the refrigerator is operating correctly.

The fr

ozen food 

compartment and cabinet work independent of each other and both must be adjusted to their 

desired

 

temperature setting.

- Touch the 

FROZEN FOOD

 COMPARTMENT [5] button to set the compartment temperature setting.

-

Using the + [4] or – [2] buttons adjust the temperature setting.

- The mode [3] will display the temperature setting

- 0 is off

- 1 is the warmest setting

- 5 is the coldest setting

- Touch the CABINET COMPARTMENT [6] button to set the

fresh food 

compartment temperature setting.

-

Using the + [4] or – [2] buttons adjust the temperature setting.

- The mode [3] will display the temperature setting

- 0 is off

- 1 is the warmest setting

- 5 is the coldest setting

- Press any button to return the control to activate mode, the mode [3] will illuminate. The display will return to standby mode after 5

seconds.

-Touch the NIGHT MODE [7] button to set the refrigerator to night mode.

- Night mode will turn off automatically after 8 hours or if you push the night mode button again to turn the blue indicator light off.

- This 8 hours can be changed by pressing the night mode button for 3 seconds. After the 3 seconds, the default 8 hour hours will be

shown in the display .  To change this setting, press the “+” or “-”, then press night mode button to make the setting go into effect.

- The new setting is archived in the memory until it is changed.

Shut down:

- To shut down the refrigerator, touch and hold the ON/OFF button [1] for 5 seconds and release

- Once the refrigerator is turned OFF there is a 5 minute wait cycle before the refrigerator can be turned ON. The refrigerator will not

turn on again until the 5 minute wait is up.

Do not operate the refrigerator when the ambient temperature is higher than 

43

° 

C

. Operation 

above the 

recommended ambient te

mperature can cause permanent damage to the compressor.

 Operation when the 

ambient temperature is higher than 43° C. can result in poor cooling performance.

Connect the Electrical Components

CAUTION

!

1

2

3

5

4

6

7

ART 02735

NOTICE

Summary of Contents for T1274










Reviews: