16
Ŗ
To take out the beautiful front cover, proceed as follows (see
figure 4):
Remove the two fixing screws "C" from beautiful plastic
front cover.
Move the front cover to "D" direction, by applying a hard
and moderated knock on its side (side without screws), to
free the trim entered into the metallic frame.
The front is free, but still joint to the equipment through
the connection bus of the control panel.
Ŗ
To put the beautiful front cover back, proceed in the reverse
way to its removing.
4.2.4.2. Rotation of control panel with LCD
panel.
90º
"A"
"B"
"C"
Take out the beautiful front
cover according to section
4.2.4.1
Fig. 5.
Rotation of the control panel with LCD over the beau-
tiful plastic front cover.
Ŗ
To make easier the message reading when the equipment is
vertically installed, it is advisable to rotate 90º clockwise the
control panel with LCD (see figure 5).
Ŗ
Also, it is advised to rotate the control panel, if any tower type
equipment requires to be assembled as rack. Consider that the
rotation of the control panel will be counter clockwise.
Ŗ
Proceed as follows:
Remove the beautiful front cover as it is stated in section
4.2.4.1
Slightly open the nails of the four trims that hold the con-
trol panel with LCD to the beautiful front cover to free it
and push inward "A" to separate both parts.
Rotate it 90º on clockwise "B" and insert it again into
the beautiful front cover till click it "C". Check the correct
closing of the fixing nails.
Put the beautiful front cover back, in the reverse way as
its removing (see section 4.2.4.1).
4.2.4.3. Vertical assembling -tower type-.
Ŗ
Rotate the control panel according to section 4.2.4.2.
Ŗ
Take the 4 plastic pieces "A" with angle shape supplied with
the equipment and joint them two by two till obtain two sup-
ports or stabilizers "B".
Ŗ
Put the UPS vertical between the two stabilizers supports "B"
(see figure 6).
"A"
"A"
"B"
Fig. 6.
Vertical -tower type- assembling.
4.2.4.4. Vertical assembling -tower type- , with
extended back up time (battery module).
Ŗ
The description of this section is based on an equipment
with only one battery module (see figure 7). For a higher
quantity of modules proceed to the connection among them.
Ŗ
Rotate the control panel of the equipment according to sec-
tion 4.2.4.2.
Ŗ
Take the 4 plastic pieces "A" with angle shape and supplied
with the UPS and the two supplied with the battery module
"B", and joint them till obtain two supports or stabilizers "C" to
hold the equipment and battery module.
Ŗ
Put the UPS and battery module on vertical position between
the stabilizers supports "C".
Ŗ
Fix the "D" metallic piece that joint UPS and battery module
by means of the supplied screws "E".
Ŗ
Regarding the connections of the UPS with the battery module,
make the following steps, but reading section 4.3.3 previously:
Connect the supplied earth joint cable "F", between the
UPS and battery module.
USER MANUAL
Thiele KG • V
orderer W
einberg 26 • D-71522 Backnang • T
el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni
c.de • www
.thiele-electronic.de
Thiele KG • V
orderer W
einberg 26 • D-71522 Backnang • T
el.:(07191)3560-0 • Fax.:(07191)3560-19 • info@thiele-electroni
c.de • www
.thiele-electronic.de
Vorderer Weinberg 26
• D-71522 Backnang •
Tel.:+49 (0)7191 3560-0 (Fax.:-19)
