background image

24.

Corrections -   a.  Air can enter the system if the fluid level is low, see problem 2, part a, or if

the suction tube is disconnected, see problem 2, part f. Also air may enter

through fittings, which are not tightened properly, so check for any leaks

around fittings or hoses. Once the source of the air is determined, the

cylinder must be bled of all air. Most air can be removed from the system

by lowering the gate to the ground to relieve all pressure from the

cylinder, unpinning the cylinder and cycling them back and forth several

times from fully extended to fully retracted and allowing the pump to

bypass through the relief valves for a few seconds in each direction.

                             b.  The flow control provided is rated at 1.5GPM or 3.0GPM. The arrow on

the flow control must point away from the cylinder, designating the

direction of the controlled flow. Correct as needed.

                             c.  Remove and disassemble the flow control and check for excessive wear

and contamination. Clean as needed and reassemble. If this does not

correct the problem replace the flow control.

If you have any questions or problems that are not covered in this guide please call Thieman’s

Engineering Department at 1-800-524-5210.

Rev. 2/21 • 5C • MP105453

Summary of Contents for Tailgates M16

























Reviews: