background image

Table of Contents

i

Linear Bushing

1. Introduction 

 1-1

1-1 

 Foreword

――――――――――――――――――――――――――――――――

1-1

1-2 

  About This Manual

――――――――――――――――――――――――――――

1-1

1-3

  Applying This Product

― ―――――――――――――――――――――――――

1-2

1-4 

  Product Support

―――――――――――――――――――――――――――――

1-2

1-5

  Product Information and THK Information

――――――――――――――――――

1-2

2. Precautions on Use

 2-1

2-1 

  Safety Related Warning Displays

― ――――――――――――――――――――

2-1

2-2 

 Handling

― ―――――――――――――――――――――――――――――――

2-1

2-3 

  Precautions on Use

― ――――――――――――――――――――――――――

2-2

2-4 

 Lubrication

― ――――――――――――――――――――――――――――――

2-3

2-5 

 Storage

― ―――――――――――――――――――――――――――――――

2-3

2-6 

 Disposal

― ―――――――――――――――――――――――――――――――

2-3

3. Assembly

 3-1

3-1 

  Mounting the Outer Cylinder

― ――――――――――――――――――――――

3-2

3-2 

  Mounting the Shaft Support 

――――――――――――――――――――――――

3-5

3-3 

  Mounting the Linear Bushing  

― ――――――――――――――――――――――

3-5

3-4

  Attaching FLM Felt Seal  

― ――――――――――――――――――――――――

3-7

4. Lubrication

 4-1

4-1 

  Lubrication Interval

― ――――――――――――――――――――――――――

4-1

www.thk.ru

тел. +7(499) 703-39-86

sales@thk.ru

Summary of Contents for Linear Bushing



















Reviews: